Cisco 300-101 (Implementing Cisco IP Routing (ROUTE v2.0)) 시험대비덤프를 찾고 계시다면 Pass4Test가 제일 좋은 선택입니다.저희 Pass4Test에서는 여라가지 IT자격증시험에 대비하여 모든 과목의 시험대비 자료를 발췌하였습니다. Pass4Test에서 시험대비덤프자료를 구입하시면 시험불합격시 Cisco 300-101 (Implementing Cisco IP Routing (ROUTE v2.0)) 덤프비용 환불신청이 가능하고 덤프 1년 무료 업데이트서비스도 가능합니다. Pass4Test를 선택하시면 후회하지 않을것입니다.

NO.1 A corporate policy requires PPPoE to be enabled and to maintain a connection with the ISP,
even if no interesting traffic exists. Which feature can be used to accomplish this task?
A. TCP Adjust
B. Dialer Persistent
C. PPPoE Groups
D. half-bridging
E. Peer Neighbor Route
Answer: B

NO.2 After you review the output of the command show ipv6 interface brief, you see that several
IPv6 addresses have the 16-bit hexadecimal value of "FFFE" inserted into the address. Based on this
information, what do you conclude about these IPv6 addresses?
A. IEEE EUI-64 was implemented when assigning IPv6 addresses on the device.
B. The addresses were misconfigured and will not function as intended.
C. IPv6 addresses containing "FFFE" indicate that the address is reserved for multicast.
D. The IPv6 universal/local flag (bit 7) was flipped.
E. IPv6 unicast forwarding was enabled, but IPv6 Cisco Express Forwarding was disabled.
Answer: A

NO.3 A network engineer executes the show ip flow export command. Which line in the output
indicates that the send queue is full and export packets are not being sent?
A. output drops
B. enqueuing for the RP
C. fragmentation failures
D. adjacency issues
Answer: A

NO.4 Refer to the following access list.
access-list 100 permit ip any any log
After applying the access list on a Cisco router, the network engineer notices that the router CPU
utilization has risen to 99 percent. What is the reason for this?
A. A packet that matches access-list with the "log" keyword is Cisco Express Forwarding switched.
B. A packet that matches access-list with the "log" keyword is fast switched.
C. A packet that matches access-list with the "log" keyword is process switched.
D. A large amount of IP traffic is being permitted on the router.
Answer: C

NO.5 SIMULATION
Route.com is a small IT corporation that is attempting to implement the network shown in the
exhibit. Currently the implementation is partially completed. OSPF has been configured on routers
Chicago and NewYork. The SO/O interface on Chicago and the SO/1 interface on NewYork are in Area
0. The loopbackO interface on NewYork is in Area 1. However, they cannot ping from the serial
interface of the Seattle router to the loopback interface of the NewYork router. You have been asked
to complete the implementation to allow this ping.
ROUTE.com's corporate implementation guidelines require:
The OSPF process ID for all routers must be 10.
The routing protocol for each interface must be enabled under the routing process.
The routing protocol must be enabled for each interface using the most specific wildcard mask
possible.
The serial link between Seattle and Chicago must be in OSPF area 21.
OSPF area 21 must not receive any inter-area or external routes.
Network Information
Seattle
S0/0 192.168.16.5/30 - Link between Seattle and Chicago
Secret Password: cisco
Chicago
S0/0 192.168.54.9/30 - Link between Chicago and NewYork
S0/1 192.168.16.6/30 - Link between Seattle and Chicago Secre
Password: cisco
NewYork
S0/1 192.168.54.10/30 - Link between Chicago and NewYork
Loopback0 172.16.189.189
Secret Password: cisco
Answer:
Note: In actual exam, the IP addressing, OSPF areas and process ID, and router hostnames may
change, but the overall solution is the same.
Seattle's S0/0 IP Address is 192.168.16.5/30. So, we need to find the network address and wildcard
mask of 192.168.16.5/30 in order to configure the OSPF.
IP Address: 192.168.16.5 /30
Subnet Mask: 255.255.255.252
Here subtract 252 from 2565, 256-252 = 4, hence the subnets will increment by 4.
First, find the 4th octet of the Network Address:
The 4th octet of IP address (192.168.16.5) belongs to subnet 1 (4 to 7).
Network Address: 192.168.16.4
Broadcast Address: 192.168.16.7
Lets find the wildcard mask of /30.
Subnet Mask: (Network Bits - 1's, Host Bits - 0's)
Lets find the wildcard mask of /30.
Now we configure OSPF using process ID 10 (note the process ID may change to something else in
real exam).
Seattle>enable
Password:
Seattle#conf t
Seattle(config)#router ospf 10
Seattle(config-router)#network 192.168.16.4 0.0.0.3 area 21
One of the tasks states that area 21 should not receive any external or inter-area routes (except the
default route).
Seattle(config-router)#area 21 stub
Seattle(config-router)#end
Seattle#copy run start
Chicago Configuration:
Chicago>enable
Password: cisco
Chicago#conf t
Chicago(config)#router ospf 10
We need to add Chicago's S0/1 interface to Area 21
Chicago(config-router)#network 192.168.16.4 0.0.0.3 area 21
Again, area 21 should not receive any external or inter-area routes (except the default route).
In order to accomplish this, we must stop LSA Type 5 if we don't want to send external routes. And if
we don't want to send inter-area routes, we have to stop LSA Type 3 and Type 4. Therefore we want
to configure area 21 as a totally stubby area.
Chicago(config-router)#area 21 stub no-summary
Chicago(config-router)#end
Chicago#copy run start
The other interface on the Chicago router is already configured correctly in this scenario, as well as
the New York router so there is nothing that needs to be done on that router.

NO.6 A network engineer is configuring SNMP on network devices to utilize one-way SNMP
notifications. However, the engineer is not concerned with authentication or encryption. Which
command satisfies the requirements of this scenario?
A. router(config)#snmp-server host 172.16.201.28 traps version 2c CISCORO
B. router(config)#snmp-server host 172.16.201.28 informs version 2c CISCORO
C. router(config)#snmp-server host 172.16.201.28 traps version 3 auth CISCORO
D. router(config)#snmp-server host 172.16.201.28 informs version 3 auth CISCORO
Answer: A

NO.7 Prior to enabling PPPoE in a virtual private dialup network group, which task must be
completed?
A. Disable CDP on the interface.
B. Execute the vpdn enable command.
C. Execute the no switchport command.
D. Enable QoS FIFO for PPPoE support.
Answer: B

NO.8 An organization decides to implement NetFlow on its network to monitor the fluctuation of
traffic that is disrupting core services. After reviewing the output of NetFlow, the network engineer is
unable to see OUT traffic on the interfaces. What can you determine based on this information?
A. Cisco Express Forwarding has not been configured globally.
B. NetFlow output has been filtered by default.
C. Flow Export version 9 is in use.
D. The command ip flow-capture fragment-offset has been enabled.
Answer: A