많은 사이트에서 Aruba Certification ACMP-6.3인증시험대비자료를 제공하고 있습니다. 그중에서 Pass4Test를 선택한 분들은 Aruba Certification ACMP-6.3시험통과의 지름길에 오른것과 같습니다. Pass4Test는 시험에서 불합격성적표를 받으시면 덤프비용을 환불하는 서비스를 제공해드려 아무런 걱정없이 시험에 도전하도록 힘이 되어드립니다. Pass4Test덤프를 사용하여 시험에서 통과하신 분이 전해주신 희소식이 Pass4Test 덤프품질을 증명해드립니다.
NO.1 ip access-list session anewone user network 10.1.1.0 255.255.255.0 any
permit user host
10.1.1.1 any deny
user any any permit
Referring to the
above portion of a Mobility Controller configuration file, what can you
conclude?
(Choose two)
A. This is a session firewall policy.
B. This is
an extended Access Control List (ACL).
C. Any traffic going to destination
10.1.1.1 will be denied.
D. Any traffic going to destination 10.2.2.2 will be
denied.
E. Any traffic going to destination 172.16.100.100 will be
permitted.
Answer: A,E
NO.2 A client device associates with an SSID
provisioned with 802.1X authentication. The client is
set for LEAP
authentication. EAP termination (AAA Fastconnect) is enabled on the controller.
But the
client continuously cycles through the authentication process. Which
of the following could cause
this?
A. The Radius server is rejecting the
client credentials.
B. The client has an expired or revoked server
certificate.
C. The DHCP server is not enabled.
D. The VLAN is missing for
the SSID.
E. The controller does not support LEAP in this mode.
Answer:
E
NO.3 When configuring ports in the Controller wizard, which of the
following are NOT configuration
options? (Choose two)
A. Inter-VLAN
routing
B. Speed
C. Trusted
D. LACP
E. Trunk
Answer:
A,D
NO.4 Which command, when executed on a master controller, will show
the APs connected to all
controllers?
A. show stm connectivity
B. show
ap active
C. show ap database
D. show ap bss-table
E. show ap
controller-lms
Answer: C
NO.5 An Aruba Controller is configured with
VLAN 1,5, 200, and 4095. All VLANs have IP addresses
assigned. Which is the
default management VLAN on the Aruba controller?
A. VLAN 5
B. VLAN 1
C.
VLAN 200
D. None, it must be defined
E. VLAN 4095
Answer: B
NO.6
Which of the statements below are TRUE regarding ARM's Spectrum Load Balancing
feature?
(Choose two)
A. Available only on 5GHz radios
B. Disabled by
default
C. Balances client load across available channels/APs
D. Enabled
by default
E. Available only on 2.4GHz radios
Answer: B,C
NO.7 If a
Remote AP (RAP) is attempting to contact a controller that is behind a NAT
device what
protocol must be allowed through the NAT/Firewall?
A.
PAPI
B. NATT
C. IPSec
D. SSH
E. GRE
Answer: B
NO.8 Which
command will show all client association history?
A. Aruba-6000# show mobile
trail current (ip address)
B. Aruba-6000# show ip mobile trail (ip
address)
C. Aruba-6000# show ap client status (mac address)
D. Aruba-6000#
show current client ip (ip address)
E. Aruba-6000# show client ip (ip
address) mobility
Answer: B
permit user host
10.1.1.1 any deny
user any any permit
Referring to the
above portion of a Mobility Controller configuration file, what can you
conclude?
(Choose two)
A. This is a session firewall policy.
B. This is
an extended Access Control List (ACL).
C. Any traffic going to destination
10.1.1.1 will be denied.
D. Any traffic going to destination 10.2.2.2 will be
denied.
E. Any traffic going to destination 172.16.100.100 will be
permitted.
Answer: A,E
NO.2 A client device associates with an SSID
provisioned with 802.1X authentication. The client is
set for LEAP
authentication. EAP termination (AAA Fastconnect) is enabled on the controller.
But the
client continuously cycles through the authentication process. Which
of the following could cause
this?
A. The Radius server is rejecting the
client credentials.
B. The client has an expired or revoked server
certificate.
C. The DHCP server is not enabled.
D. The VLAN is missing for
the SSID.
E. The controller does not support LEAP in this mode.
Answer:
E
NO.3 When configuring ports in the Controller wizard, which of the
following are NOT configuration
options? (Choose two)
A. Inter-VLAN
routing
B. Speed
C. Trusted
D. LACP
E. Trunk
Answer:
A,D
NO.4 Which command, when executed on a master controller, will show
the APs connected to all
controllers?
A. show stm connectivity
B. show
ap active
C. show ap database
D. show ap bss-table
E. show ap
controller-lms
Answer: C
NO.5 An Aruba Controller is configured with
VLAN 1,5, 200, and 4095. All VLANs have IP addresses
assigned. Which is the
default management VLAN on the Aruba controller?
A. VLAN 5
B. VLAN 1
C.
VLAN 200
D. None, it must be defined
E. VLAN 4095
Answer: B
NO.6
Which of the statements below are TRUE regarding ARM's Spectrum Load Balancing
feature?
(Choose two)
A. Available only on 5GHz radios
B. Disabled by
default
C. Balances client load across available channels/APs
D. Enabled
by default
E. Available only on 2.4GHz radios
Answer: B,C
NO.7 If a
Remote AP (RAP) is attempting to contact a controller that is behind a NAT
device what
protocol must be allowed through the NAT/Firewall?
A.
PAPI
B. NATT
C. IPSec
D. SSH
E. GRE
Answer: B
NO.8 Which
command will show all client association history?
A. Aruba-6000# show mobile
trail current (ip address)
B. Aruba-6000# show ip mobile trail (ip
address)
C. Aruba-6000# show ap client status (mac address)
D. Aruba-6000#
show current client ip (ip address)
E. Aruba-6000# show client ip (ip
address) mobility
Answer: B