Pass4Test 의 Juniper JN0-694덤프는 PDF버전과 소프트웨어버전 두가지 버전으로 되어있는데 소프트웨어버전은 시뮬레이션버전입니다. 소프트웨어버전의 문제를 푸는 과정은 시험현장을 연상케하여 시험환경에 먼저 적응하여 실제시험에서 높은 점수를 받도록 도와드릴수 있습니다.

 

 

 

NO.1 You are having problems redistributing RIP routes into OSPF. Your Junos device has the
following configuration:
[edit protocols ospf]
user@router# show
import my-policy;
area 0.0.0.0 {
interface ge-0/ 0/ 0.0;
interface ge-0/ 0/ ;
interface ge-0/ 0/ {
passive;
}
}
What would resolve the problem?
A. Apply my-policy as an export policy under the [edit protocols rip] hierarchy.
B. Apply my-policy as an import policy under the [edit protocols rip] hierarchy.
C. Apply my-policy as an export policy under the [edit protocols ospf] hierarchy.
D. Use the area-range parameter instead of a routing policy.
Answer: D

NO.2 Your Layer 2 network uses VLAN IDs 100 through 400 and you are required to load-balance
these VLANs between two different root bridges. You are currently using the default RSTP settings
and notice that all VLANs are using the same root bridge.
How do you ensure the VLANs are load-balanced between two root bridges?
A. Configure MSTP with two MSTI regions and split the VLAN range between them.
B. Configure VSTP with two VLAN groups and split the VLAN range between them.
C. Configure two RSTP instances and split the VLAN range between them.
D. Configure STP and RSTP and split the VLAN range between them.
Answer: A

NO.3 Your Junos device is dropping certain traffic flows, while allowing other traffic flows to pass
through the device unaffected.
Which CoS component is causing this problem?
A. BA classification
B. RED
C. MF classification
D. Rewrite rules
Answer: D

NO.4 You are troubleshooting a problem where an OSPF adjacency between two neighboring
routers will not form.
What are two reasons for this problem? (Choose two.)
A. One or both of the connected interfaces are missing the family inet statement.
B. One or both of the connected interfaces are missing the family iso statement.
C. The connected interfaces are not on the same subnet.
D. Another IGP is running on one or both of the routers, overriding OSPF.
Answer: B,D

NO.5 Your switch is experiencing a problem where a port that should have only one host connected
occasionally shows that multiple MAC addresses are being learned.
Which configuration setting would ensure that no extra hosts can join the network using this switch
port?
A. mac-limit
B. no-mac-learning
C. persistent-learning
D. bpdu-block-on-edge
Answer: D

NO.6 You are implementing Q-in-Q tunneling on an EX Series switch. You want the tunnel to support
all C-VLANs; however, only some VLANs are able to send traffic across the tunnel.
Switch-1 has the following configuration:
[edit vlans]
user@Switch-1# show
v100 {
vlan-id 100;
interface {
ge-0/ 0/ 0.10;
ge-0/ 0/1.20;
}
dot1q-tunneling {
customer-vlans [ ];
}
}
What would solve this problem?
A. Add family ethernet-switching to the tunnel-side interface on Switch-1.
B. Implement RSTP .
C. Q-in-Q tunneling will not work in this scenario; use a Layer 2 VPN instead.
D. Remove the customer-vlans statement.
Answer: C

NO.7 You observe that a router is using an unusually high amount of CPU cycles.
You determine that continuous SPF calculations in OSPF are being performed.
What are two reasons for this problem? (Choose two.)
A. The wrong authentication keys between the OSPF neighbors are used.
B. The interface MTU is mismatched between the OSPF neighbors.
C. There are duplicate router IDs within the OSPF area.
D. An OSPF adjacency is flapping.
Answer: C,D

NO.8 Two neighboring routers are able to form an OSPF adjacency, but are not able to establish an
IBGP neighborship.
What are two reasons for the IBGP neighborship problem? (Choose two.)
A. One of the devices has a misconfigured BGP peer address.
B. One or both of the connected interfaces are missing the family iso statement.
C. OSPF has a lower route preference than BGP .
D. A firewall filter on one of the interfaces is blocking TCP traffic.
Answer: B,C