Cisco 650-296 (TelePresence Video Sales Engineer for Advanced Exam) 시험패스는 IT업계종사자들이 승진 혹은 연봉협상 혹은 이직 등 보든 면에서 날개를 가해준것과 같습니다.IT업계는  Cisco 650-296 (TelePresence Video Sales Engineer for Advanced Exam) 시험을 패스한 전문가를 필요로 하고 있습니다. Pass4Test의 Cisco 650-296 (TelePresence Video Sales Engineer for Advanced Exam) 덤프로 시험을 패스하고 자격증을 취득하여 더욱더 큰 무대로 진출해보세요.

 

 

NO.1 Refer to the exhibit,
Which deployment model is represented.?
A. campus multizone
B. WAN multizone
C. campus single zone
D. WAN single zone
Answer: D

NO.2 Why would you include include a gateway in your design?
A. Gateways assist in video and conferencing integration
B. Gateways allow for simplification of the address plan by elimination the need for dialing a full PSTN
number
C. Gateways provide network translation if varying protocols are used
D. Gateways are required to integrate multiple endpoints
Answer: C

NO.3 Which of these is an advantage of the multizone model VCS with Prefix Dialing?
A. Location requests are only sent to the relevant zone
B. Location VCS servers only need to know about the directory VCS and do not need to know about any
other local VCS
C. When adding a new zone, only the directory gatekeeper needs to be configured
D. All gatekeepers know about all calls at times
Answer: A

NO.4 Which two of these configurations must be applied when dialing from an IP endpoint to an ISDN
destination? (Choose two)
A. A dial plan rule must be created
B. Gateway services numbers should mimic incoming PSIT routing methods
C. The Cisco TelePresence Software Version TC4.0 protocol is required
D. DID mapping must be configured on the ISDN gateway Build Your Dreams
E. A prefix must be registered with the gatekeeper
Answer: AE

NO.5 Which MSE blade provides high-definition multipoint control unit support?
A. Cisco MSE 8510 Media2
B. Cisco MSE 8420 Media
C. Cisco MSE 8350 IP GW
D. Cisco MSE 8220 VCR
Answer: A

NO.6 Your network uses a combination of SIP and H.323 endpoints. When planning to implement firewalls for
security, what device permits traversal of the firewall for there devices?]
A. Gateway
B. VCS Expressway
C. Tandberg Management Suite
D. multipoint control unit
E. Cisco TelePresence
Answer: B

NO.7 Which of these is a disadvantage of a single-zone (VCS) WAN model?
A. No endpoints will be able to place calls if connectivity is lost to the VCS location
B. Not all signaling goes through the VCS in the headquarters, causing signaling traffic across the WAN
link
C. If interworking is required, the media does not go through the VCS in the headquarters, even if the
video call is from a branch office endpoint to another endpoint in that office
D. Flexibility cannot be assured in the headquarters configuration
Answer: A

NO.8 Which three methods can be used to start a conference with the Cisco TelePresence Video
Communication Server? (Choose three)
A. Use the web interface of the Cisco TelePresence Video Communication Server
B. Use the Cisco TelePresence System user interface
C. Call directly into a conference from an endpoint
D. Use a FindMe connetion
E. Connect to a VCS Expressway from an IP endpoint
F. Receive a request-for-conference call from a connected user
G. Use the Cisco TelePresence remote control
Answer: BCG

NO.9 How does the VCS Expressway allow secure traversal of a firewall?
A. It uses a designated port to allow all traffic to pass through the firewall
B. It takes the place of a firewall to control trusted messages using a pre-set list of destinations
C. It makes outbound connections only
D. It prohibits all incoming and outgoing message from untrusted destinations
Answer: C

NO.10 Which two of these tasks should be completed to enable calls through a firewall? (Choose two)
A. Create one traversal server zone on the VCS Expressway for any VCS Control that is running a
traversal client
B. Configure the traversal server zone with details of the corresponding zone on the traversal client
C. Create a traversal server zone on your local VCS Control Build Your Dreams
D. Configure VCS with details of the corresponding zone on the traversal server
E. Create a traversal client zone on your local VCS Control
Answer: AE