Pass4Test의 Cisco인증 200-105자격증는 IT인사들의 많은 찬양을 받아왔습니다.이는Pass4Test의 Cisco인증 200-105자격증가 신뢰성을 다시 한번 인증해주는것입니다. Cisco인증 200-105자격증의 인기는 이 시험과목이 얼마나 중요한지를 증명해줍니다. Pass4Test의 Cisco인증 200-105자격증로 이 중요한 IT인증시험을 준비하시면 우수한 성적으로 시험을 통과하여 인정받는 IT전문가로 될것입니다.
취직을 원하시나요? 승진을 원하시나요? 연봉인상을 원하시나요? 무엇을 원하시든 국제적으로 인정받은 IT인증자격증을 취득하는것이 길입니다. Cisco인증 200-125국제자격증은 널리 인정받는 인기자격증의 시험과목입니다. Cisco인증 200-125국제자격증을 패스하여 자격증을 취득하면 소원이 이루어집니다. Pass4Test의Cisco인증 200-125국제자격증는 시험패스율이 높아Cisco인증 200-125국제자격증준비에 딱 좋은 공부자료입니다. Pass4Test에서 덤프를 마련하여 자격증취득에 도전하여 인생을 바꿔보세요.
시험 번호/코드: 200-105시험 이름: Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0)
당신이 구입하기 전에 시도, 100% 합격율 보장
100% 환불보장약속 200-105자격증
PDF 및 소프트웨어, 연구와 실천
시험 번호/코드: 200-125시험 이름: CCNA Cisco Certified Network Associate CCNA (v3.0)
당신이 구입하기 전에 시도, 100% 합격율 보장
100% 환불보장약속 200-125국제자격증
PDF 및 소프트웨어, 연구와 실천
Cisco 인증 200-125국제자격증에 도전해보려고 결정하셨다면 Pass4Test덤프공부가이드를추천해드립니다. Pass4Test덤프는 고객님께서 필요한것이 무엇인지 너무나도 잘 알고 있답니다. Pass4Test의 Cisco 인증 200-125국제자격증는Cisco 인증 200-125국제자격증을 쉽게 만듭니다.
200-125 덤프무료샘플다운로드하기: http://www.pass4test.net/200-125.html
NO.1 Refer to the exhibit.
At the end of an RSTP election process, which
access layer switch port will assume the discarding
role?
A. Switch3, port
Gi0/1
B. Switch4, port fa0/11
C. Switch3, port fa0/12
D. Switch3, port
Gi0/2
E. Switch3, port fa0/1
F. Switch4, port fa0/2
Answer:
B
200-125덤프 200-125교육
Explanation:
In
this question, we only care about the Access Layer switches (Switch3 & 4).
Switch 3 has a lower
bridge ID than Switch 4 (because the MAC of Switch3 is
smaller than that of Switch4) so both ports of
Switch3 will be in forwarding
state. The alternative port will surely
belong to Switch4.
Switch4 will
need to block one of its ports to avoid a bridging loop between the
two
switches. But how does Switch4 select its blocked port? Well, the answer
is based on the
BPDUs it receives from Switch3. A BPDU is superior to another
if it has:
1.A lower Root Bridge ID
2.A lower path cost to the Root
3.A
lower Sending Bridge ID
NO.2 An administrator is trying to ping and
telnet from SwitchC to RouterC with the results shown
below.
Click the
console connected to RouterC and issue the appropriate commands to answer
the
questions.
What would be the effect of issuing the command ip
access-group 115 in on the s0/0/1 interface?
A. Only traffic from the
10.4.4.0 network would pass through the interface.
B. No host could connect
to RouterC through s0/0/1.
C. FTP, FTP-DATA, echo, and www would work but
telnet would fail.
D. Telnet and ping would work but routing updates would
fail.
Answer: B
200-125시험정보 200-125
dump
Explanation:
First let's see what was configured on interface
S0/0/1:
NO.3 Refer to the exhibit.
What is the meaning of the term
dynamic as displayed in the output of the show frame-relay map
command
shown?
A. The mapping between DLCI 100 and the end station IP address
172.16.3.1 was learned through
Inverse ARP.
B. The Serial0/0 interface is
passing traffic.
C. The DLCI 100 will be dynamically changed as required to
adapt to changes in the Frame Relay
cloud.
D. The DLCI 100 was dynamically
allocated by the router.
E. The Serial0/0 interface acquired the IP address
of 172.16.3.1 from a DHCP server.
Answer: A
200-125
dump
Explanation:
Inverse Address Resolution Protocol (Inverse ARP) was
developed to provide a mechanism for
dynamic DLCI to Layer 3 address maps.
Inverse ARP works much the same way Address Resolution
Protocol (ARP) works
on a LAN. However, with ARP, the device knows the Layer 3 IP address
and
needs to know the remote data link MAC address. With Inverse ARP, the
router knows the Layer 2
address which is the DLCI, but needs to know the
remote Layer 3 IP address. When using dynamic
address mapping, Inverse ARP
requests a next-hop protocol address for each active PVC. Once the
requesting
router receives an Inverse ARP response, it updates its DLCI-to-Layer 3 address
mapping
table. Dynamic address mapping is enabled by default for all
protocols enabled on a physical
interface. If the Frame Relay environment
supports LMI autosensing and Inverse ARP, dynamic
address mapping takes place
automatically. Therefore, no static address mapping is required.
NO.4
Which three elements must be used when you configure a router interface for VLAN
trunking?
(Choose three.)
A. one subinterface per VLAN
B. subinterface
numbering that matches VLAN tags
C. one physical interface for each
subinterface
D. subinterface encapsulation identifiers that match VLAN
tags
E. a management domain for each subinterface
F. one IP network or
subnetwork for each subinterface
Answer: A,D,F
200-125기출문제 200-125
dumps
Explanation:
This scenario is commonly called a router on a
stick. A short, well written article on this operation can
be found
here:
http://www.thebryantadvantage.com/RouterOnAStickCCNACertificationExamTutorial.htm