IT인증,IT자격증,IT자격증시험,IT인증시험

http://www.pass4test.net/

IBM A4040-221 (Assessment: AIX 7 Administration ) 인증자료

Pass4Test는 IT인증자격증을 취득하려는 IT업계 인사들의 검증으로 크나큰 인지도를 가지게 되었습니다. 믿고 애용해주신 분들께 감사의 인사를 드립니다.IBM A4040-221 (Assessment: AIX 7 Administration ) 덤프도 다른 과목 덤프자료처럼 적중율 좋고 통과율이 장난이 아닙니다. 덤프를 구매하시면 퍼펙트한 구매후 서비스까지 제공해드려 고객님이 보유한 덤프가 항상 시장에서 가장 최신버전임을 약속해드립니다.IBM A4040-221 (Assessment: AIX 7 Administration ) 덤프만 구매하신다면 자격증 취득이 쉬워져 고객님의 밝은 미래를 예약한것과 같습니다.







NO.1 Which technology provides the maximum amount of usable storage and resilience for a

system with 6 physical volumes?

A. RAID 0

B. RAID 1

C. RAID 5

D. RAID 6

Answer: C




NO.2 The following information has been reported in an AIX error log:

How can the administrator prevent the error from reoccurring?

A. Create a secondary dump device greater than 266MB

B. Increase primary dump device size greater than 266MB

C. Increase "/var" file system to ensure it has a minimum of 266MB free space

D. Increase "/var/adm/ras/livedump" file system to ensure it has a minimum of 266MB free space

Answer: C




NO.3 An LPAR is configured with strict logical volume mirroring across two disks for resilience. The

administrator would like to ensure if one disk fails the volume group stays online. Which command

will ensure that the datavg volume group stays online?

A. varyonvg -n datavg

B. mirrorvg-Q-c 2 datavg

C. mklvcopy -e m -s y (each logical volume name) 2

D. chvg -Qn datavg

Answer: D




NO.4 A host has a single virtual Ethernet adapter (ent0) configured with only a default PVID, and the

administrator is trying to determine why it cannot be used to reach any other system on the

network. He suspects that it may be caused by a problem in the VLAN configuration.

How would the administrator determine the VLAN for which the adapter was configured?

A. Use the command 'Isdev -I ent0' on the host to determine the port VLAN ID.

B. Use the command 'Isattr-EI ent0' on the host to determine the port VLAN ID.

C. Look on the HMC to determine which VLAN is configured for the adapter.

D. Examine the Shared Ethernet Adapter on the Virtual I/O Server to determine which VLAN the

adapter is using.

Answer: C




NO.5 What is the difference between deferred and concurrent firmware updates?

A. Deferred firmware can be applied concurrently but contains updates that affect the internal

program load path, which are not activated until the next time the server is shut down and restarted.

B. Concurrent firmware must be done on all LPARs in the frame at the same time. Deferred

firmware can be loaded on each LPAR at a different time and only becomes active when the LPAR is

shutdown and restarted.

C. Deferred firmware can only be applied during an outage to the managed system as it will

automatically shut the managed system down during its installation.

D. Concurrent firmware is only for minor fixes to the system mircocode while deferred firmware

contains major fixes to the service processor.

Answer: A




NO.6 After performing a NIM rte install, the administrator noticed that not all filesets are at the

correct Technology Level (TL). What action will help the administrator determine why the

inconsistent fileset levels were installed?

A. On the NIM server, run an Ippchk to identify if the Software Vital Product Data is valid.

B. On the NIM client, run oslevel command against the TL to identify missing prerequisites.

C. Run instfix command on NIM client to determine what filesets are inconsistent.

D. On the NIM server run the NIM IsIpp command to indentify downlevel filesets contained in the

lpp_source.

Answer: D




NO.7 What is a requirement for Live Partition Mobility?

A. The network and disk must be virtual.

B. The disk must be virtual and a Logical Host Ethernet Adapter (LHEA) for network.

C. The client partition must be connected to a SAN.

D. The client partition must be set up as a 'Mover Service Partition'.

Answer: A




NO.8 How can an administrator disable Role Based Access Control (RBAC) in a WPAR?

A. Run chattr -E -I sys0 -a enhanced_RBAC=false Reboot the WPAR

B. Run the RBAC wizard and deselect 'Enable RBAC Reboot the system

C. Run chdev -I mywpar -a enhanced_RBAC=false Reboot the Global Environment

D. Run chwpar -a RBAC=false Reboot the WPAR

Answer: C




Posted 2014/7/7 15:03:23  |  Category: IBM  |  Tag: A4040-221인증자료