IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2) 인증시험은 현재 IT인사들 중 아주 인기 있는 인증시험입니다.IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2) 시험패스는 여러분의 하시는 일과 생활에서 많은 도움을 줄 뿐만 아니라 중요한 건 여러분의 IT업계에서의 자기만의 자리를 지키는 유력한 조건입니다. 이렇게 좋은 시험이니 많은 분들이 응시하려고 하는데 패스율은 아주 낮습니다.Pass4Test는 IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2) 인증시험을 아주 쉽게 패스할 수 있도록 도와드리는 사이트입니다. Pass4Test의 엘리트한 전문가가 끊임없는 노력으로 최고의 IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2) 자료를 만들었습니다. 이 자료로 여러분은 100%  IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2) 인증시험을 패스할 수 있으며Pass4Test을 선택함으로 성공을 선택한 것과 같습니다. Pass4Test가 제공하는 시험가이드로 효과적인 학습으로 많은 분들이 모두 인증시험을 패스하였습니다. 이건 모두 Pass4Test 인증시험덤프로 시험준비를 하셨기 때문입니다. 그 중  IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2) 인증시험을 패스한 분들도  Pass4Test인증시험 덤프를 사용하셨기 때문입니다.

 

 

NO.1 An administrator is using PowerHA 7 to define a new cluster using SMIT option "Setup a Cluster, Nodes
and Networks" and encountered the following error message:
What is the root cause of the problem?
A. The nodes were not defined in the DNS
B. The /etc/cluster/rhosts are not populated correctly
C. The CAA repository disk is not accessible on all nodes
D. The CAA cluster was not defined before defining the PowerHA Cluster
Answer: B

NO.2 The service IPs VLAN is the only routable network in a 2-node HA cluster with multiple network
interfaces. What must done to enable administrative tasks to be performed remotely on the cluster
nodes?
A. Associate a permanent Service IP address for each HA node.
B. Configure the boot IP Address on the same VLAN as the service IP Address.
C. Configure a persistent IP Address for each node on the service IP network.
D. Create a route on the switch and translate the Service IP address to the boot IP address using NAT.
Answer: C

NO.3 There is a two-node cluster with Node1 and Node2. An administrator changes filesystem size on Node1
by using the chfs command, and moves resource the group to Node2.
The administrator finds the change of filesystem size is recognized on Node2.
Why is the filesystem size change reflected on Node2?
A. The gsclvmd daemon automatically synchronizes filesystem changes.
B. The filesystem size change is recognized when filesystem is mounted on Node2.
C. A pre-event is defined to get_disk_vg_fs event to reflect filesystem size change.
D. The shared volume group is re-imported on Node2 by lazy update when moving the resource group.
Answer: A

NO.4 An administrator is planning to upgrade from HACMP 5.5 and AIX 5.3 to PowerHA 7 and AIX 7. After
migration installing AIX, what must be done first?
A. Install CAAfileset.
B. Migrate to PowerHA 7.
C. Run the clmigcheck program.
D. Create shared VG for use by CAA.
Answer: C

NO.5 A 2-node cluster has three multi-node disk heartbeat (MNDHB) networks and data volume groups on
separate disks. Application resource groups are online on Node1. What happens if Node1 loses access to
two of the three MNDHB disks?
A. Node1 halts
B. Application resource groups move to Node2
C. Application resource groups remain on Node1
D. Application resource groups on Node1 go offline
Answer: B

NO.6 Consider the following PowerHA DLPAR configuration for a cluster, and LPAR profile on the HMC for a
standby node in that cluster: How should the standby node profile be reconfigured so that an application
runs with the minimum hardware resources?
A. Minimum and Desired processing units = 0.1 and Maximum processing units = 0.6
B. Minimum and Desired processing units = 0.2 and Maximum processing units = 0.5
C. Minimum processing units = 0.6 and both Desired and Maximum processing units = 1.5
D. Minimum processing units = 0.5 and both Desired and Maximum processing units = 0.9
Answer: D

NO.7 Given the information from hacmp.out below, why is the cluster in config_too_long status?
A. The script /APP1/serv/scripts/shut_down does not exist.
B. The APP1 stop_server script exited with a non zero return code.
C. The application did not shut down correctly, which caused the rg_move operation to exceed the time
limit to complete.
D. The rg_move event is sleeping for anything between 360 seconds and 3600 hours until the
stop_server script is complete.
Answer: B

NO.8 What cluster service settings can be defined in SMIT on one node of a cluster and automatically
updated on all other nodes?
A. BROADCAST message at startup
B. Start HACMP at system restart
C. Verify Cluster Prior to Startup
D. Startup Cluster Information Daemon
Answer: A

NO.9 When implementing PowerHA in a cross site LVM configuration, which logical volume option is
required.?
A. Serialize IO=yes
B. Mirror Write Consistency=on
C. Scheduling Policy=sequential
D. Allocation Policy=superstrict
Answer: D

NO.10 When PowerHA SystemMirror 7.1 is installed on AIX 7.1, what RSCT component does Cluster Aware
AIX (CAA) replace?
A. Group Services
B. Resource Manager
C. Topology Services
D. Resource Monitoring and Control (RMC)
Answer: A