21세기 IT업계가 주목 받고 있는 시대에 그 경쟁 또한 상상 할만 하죠!  it업계 중 IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2) 인증시험도 아주 인기가 많은 시험입니다. 응시자는 매일매일 많아지고 있으며 패스하는 분들은 관련it업계에서 많은 지식과 내공을 지닌 분들뿐입니다.Pass4Test 는 여러분의 it전문가 꿈을 이루어 드리는 사이트 입다. Pass4Test는 여러분이 우리 자료로 관심 가는 인중시험에 응시하여 안전하게 자격증을 취득할 수 있도록 도와드립니다. 아직도 IBM 000-332 (High Avai lability for AIX - Technical Support and Administration -v2) 인증시험으로 고민하시고 계십니까?IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2) 인증시험 가이드를 사용하실 생각은 없나요? Pass4Test는 여러분께 편리를 드릴 수 있습니다.Pass4Test의 자료는 시험대비 최고의 덤프로 시험패스는 문제 없습니다. Pass4Test의 퍼펙트한 덤프인 IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2) 인증시험 자료의 문제와 답만 열심히 공부하면 여러분은 완전 안전히 IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2) 인증 자격증을 취득하실 수 있습니다.IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2)  인증시험이 이토록 인기가 많으니 우리 Pass4Test에서는 모든 힘을 다하여여러분이 응시에 도움을 드리겠으며 또 일년무료 업뎃서비스를 제공하며  Pass4Test 선택으로 여러분은 자신의 꿈과 더 가까워질 수 있습니다. 희망찬 내일을 위하여 Pass4Test선택은 정답입니다. Pass4Test선택함으로 당신이 바로 진정한 IT인사입니다.

 

 

NO.1 There is a two-node cluster with Node1 and Node2. An administrator changes filesystem size on Node1
by using the chfs command, and moves resource the group to Node2.
The administrator finds the change of filesystem size is recognized on Node2.
Why is the filesystem size change reflected on Node2?
A. The gsclvmd daemon automatically synchronizes filesystem changes.
B. The filesystem size change is recognized when filesystem is mounted on Node2.
C. A pre-event is defined to get_disk_vg_fs event to reflect filesystem size change.
D. The shared volume group is re-imported on Node2 by lazy update when moving the resource group.
Answer: A

NO.2 A 2-node cluster has three multi-node disk heartbeat (MNDHB) networks and data volume groups on
separate disks. Application resource groups are online on Node1. What happens if Node1 loses access to
two of the three MNDHB disks?
A. Node1 halts
B. Application resource groups move to Node2
C. Application resource groups remain on Node1
D. Application resource groups on Node1 go offline
Answer: B

NO.3 The service IPs VLAN is the only routable network in a 2-node HA cluster with multiple network
interfaces. What must done to enable administrative tasks to be performed remotely on the cluster
nodes?
A. Associate a permanent Service IP address for each HA node.
B. Configure the boot IP Address on the same VLAN as the service IP Address.
C. Configure a persistent IP Address for each node on the service IP network.
D. Create a route on the switch and translate the Service IP address to the boot IP address using NAT.
Answer: C

NO.4 An administrator is using PowerHA 7 to define a new cluster using SMIT option "Setup a Cluster, Nodes
and Networks" and encountered the following error message:
What is the root cause of the problem?
A. The nodes were not defined in the DNS
B. The /etc/cluster/rhosts are not populated correctly
C. The CAA repository disk is not accessible on all nodes
D. The CAA cluster was not defined before defining the PowerHA Cluster
Answer: B

NO.5 When PowerHA SystemMirror 7.1 is installed on AIX 7.1, what RSCT component does Cluster Aware
AIX (CAA) replace?
A. Group Services
B. Resource Manager
C. Topology Services
D. Resource Monitoring and Control (RMC)
Answer: A

NO.6 When implementing PowerHA in a cross site LVM configuration, which logical volume option is
required.?
A. Serialize IO=yes
B. Mirror Write Consistency=on
C. Scheduling Policy=sequential
D. Allocation Policy=superstrict
Answer: D

NO.7 An administrator is planning to upgrade from HACMP 5.5 and AIX 5.3 to PowerHA 7 and AIX 7. After
migration installing AIX, what must be done first?
A. Install CAAfileset.
B. Migrate to PowerHA 7.
C. Run the clmigcheck program.
D. Create shared VG for use by CAA.
Answer: C

NO.8 Given the information from hacmp.out below, why is the cluster in config_too_long status?
A. The script /APP1/serv/scripts/shut_down does not exist.
B. The APP1 stop_server script exited with a non zero return code.
C. The application did not shut down correctly, which caused the rg_move operation to exceed the time
limit to complete.
D. The rg_move event is sleeping for anything between 360 seconds and 3600 hours until the
stop_server script is complete.
Answer: B

NO.9 Consider the following PowerHA DLPAR configuration for a cluster, and LPAR profile on the HMC for a
standby node in that cluster: How should the standby node profile be reconfigured so that an application
runs with the minimum hardware resources?
A. Minimum and Desired processing units = 0.1 and Maximum processing units = 0.6
B. Minimum and Desired processing units = 0.2 and Maximum processing units = 0.5
C. Minimum processing units = 0.6 and both Desired and Maximum processing units = 1.5
D. Minimum processing units = 0.5 and both Desired and Maximum processing units = 0.9
Answer: D

NO.10 What cluster service settings can be defined in SMIT on one node of a cluster and automatically
updated on all other nodes?
A. BROADCAST message at startup
B. Start HACMP at system restart
C. Verify Cluster Prior to Startup
D. Startup Cluster Information Daemon
Answer: A