IT인증,IT자격증,IT자격증시험,IT인증시험

http://www.pass4test.net/

JNCIP JN0-660 (Service Provider Routing and Switching, Professional) 관련 최신, 최고의 자료

JNCIP JN0-660 (Service Provider Routing and Switching, Professional) 인증시험은 난이도가 높아 패스하기 어렵습니다. JNCIP JN0-660 (Service Provider Routing and Switching, Professional)  시험은IT업계에서도 권위가 있고 직위가 있으신 분들이 응시할 수 있는 시험이라고 알려져 있습니다. 우리Pass4Test에서는   JNCIP JN0-660 (Service Provider Routing and Switching, Professional)  관련 학습가이드를 제공합니다. Pass4Test 는 우리만의 IT전문가들이 만들어낸  JNCIP JN0-660 (Service Provider Routing and Switching, Professional)  관련 최신, 최고의 자료와 학습가이드를 준비하고 있습니다.  여러분의   JNCIP JN0-660 (Service Provider Routing and Switching, Professional)  시험에 응시하는데 많은 도움이 될 것입니다.Pass4Test를 선택하였다면 여러분은 반은 성공한 것입니다. 여러분은 아주 빠르게 안전하게 또 쉽게  JNCIP JN0-660 (Service Provider Routing and Switching, Professional)  인증시험 자격증을 취득하실 수 있습니다. 우리 Pass4Test에서 제공되는 모든 덤프들은 모두 100%합격율을 자랑하며 제일 퍼펙트한 서비스를 제공해드립니다.여러분은  JNCIP JN0-660 (Service Provider Routing and Switching, Professional)  인증시험을 패스함으로 IT업계관련 직종에 종사하려는 분들에게는 아주 큰 가산점이 될수 있으며, 성공한 IT업계전문가와 한걸음 가까워 집니다.

 

 

NO.1 Click the Exhibit button.
All routers in the exhibit are running IS-IS level 2 routing. The wide-metrics-only parameter is configured
on all routers. Which metric does R1 see for the path to R4?
A. 136
B. 138
C. 310
D. 320
Answer: D

NO.2 Click the Exhibit button.
In the exhibit, Area 1 is a not-so-stubby area.
Three networks are redistributed into Area 1 on R2.
You must summarize the redistributed network addresses in Area 1 so that only one network prefix is
re-advertised into Area 0. You must also summarize the loopback addresses of R1 and R2 into a single
address in Area 0.Which configuration sample on R3 and R5 will complete this task?
A. Option A
B. Option B
C. Option C
D. Option D
Answer: C

NO.3 You are the administrator for a network that uses IBGP. As the network grows, you must examine
options to support increased scale.
Which two scaling options should you consider? (Choose two.)
A. route reflection
B. areas
C. zones
D. confederations
Answer: B, C

NO.4 Your multicast receivers are indirectly connected to an MX Series router. The receivers need to join
multicast group 224.2.2.2. What must be configured in IGMP to receive report messages from receivers
that are multiple hops away?
A. By default, IGMP accepts report messages from indirectly connected receivers.
B. Promiscuous mode must be enabled in IGMP.
C. Promiscuous mode must be disabled in IGMP.
D. DVMRP protocol must be configured.
Answer: B

NO.5 Click the Exhibit button.
All networks shown in the exhibit contain more than one BGP speaking router. You operate ISP A.
You must ensure that customer Y sends their traffic to you over the directly connected link but customer Y
is not used for transit into your network. What do you do to accomplish this? A. Advertise routes to
customer Y with the well-known no-transit community.
B. Advertise routes to customer X with the well-known no-advertise community.
C. Advertise routes to customer Y with the well-known no-export community.
D. Advertise routes to customer X with the well-known as-transit community.
Answer: C

NO.6 Click the Exhibit button.
In the exhibit, ISP A is charged a higher rate for traffic sent to R2. You are asked to lower costs for ISP A
by configuring R1 to send traffic to R3 whenever possible.
What are two ways to do this? (Choose two.)
A. set protocols bgp group isp-b neighbor 192.0.2.6 local-preference 120
B. set protocols bgp group isp-b neighbor 192.0.2.6 local-preference 80
C. set protocols bgp group isp-b neighbor 192.0.2.10 local-preference 120
D. set protocols bgp group isp-b neighbor 192.0.2.10 local-preference 80
Answer: B, C

NO.7 In which two ways does VPLS populate the MAC table? (Choose two.)
A. dynamically using BGP
B. dynamically using the source MAC address on received frames
C. dynamically using LDP
D. statically using CLI
Answer: B, D

NO.8 Which operational mode command displays the number of configured forwarding classes?
A. show interfaces queue ge-1/0/0
B. show interfaces terse
C. show class-of-service interface
D. show forwarding classes
Answer: A

NO.9 Click the Exhibit button.
Referring to the exhibit, which type of traffic protection mechanism is used for the LSP?
A. fast-reroute
B. link-protection
C. node-link-protection
D. secondary
Answer: B

NO.10 Click the Exhibit button.
Given the drop profile in the exhibit, what is the drop probability when the buffer reaches 90% full?
A. 60%
B. 70%
C. 85%
D. 90%
Answer: B

NO.11 Click the Exhibit button.
Referring to the exhibit, which MPLS feature was used to make the LSP the preferred path for internal
routes.?
A. traffic engineering bgp-igp
B. traffic engineering shortcuts
C. traffic engineering mpls-forwarding
D. install active
Answer: C

NO.12 Click the Exhibit button.
As shown in the exhibit, you have an adaptive LSP that requires 85 Mbps. The LSP is configured with a
primary path and a secondary path in standby mode. All connections in the MPLS network are Fast
Ethernet. Which statement is correct?
A. The primary and secondary paths are in an up state and operational.
B. The primary and secondary paths are in a down state and not operational.
C. The secondary path is in a down state and not operational.
D. The primary path is in a down state and not operational.
Answer: A

NO.13 Click the Exhibit button.
Based on the configuration in the exhibit, which statement is correct?
A. The 172.20.20.0/24 route is installed in the inet.0 table with the next hop of the LSP.
B. The 172.20.20.0/24 route is installed in the mpls.0 table with the next hop of the LSP.
C. The 172.20.20.0/24 route is installed in the inet.3 table with the next hop of the LSP.
D. The 172.20.20.0/24 route is installed in the inet6.3 table with the next hop of the LSP.
Answer: C

NO.14 Click the Exhibit button.
You are asked to configure an OSPF network based on the topology shown in the exhibit. You must keep
the link-state database in Area 1 as small as possible. What will accomplish this?
A. Area 0 should be configured as a stub area so that it will not announce routes into Area 1.
B. Area 1 should be configured as an NSSA to limit the size of the link-state database.
C. Area 1 should be configured as a stub area with no-summaries to limit the size of the link-state
database.
D. Area 0 should be configured with a virtual link to R4 to limit the size of the Area 1 link-state database.
Answer: C

NO.15 Which two statements are true about OSPFv3? (Choose two.)
A. OSPFv3 uses a 32-bit router ID to uniquely identify a node in the network.
B. OSPFv3 uses a 128-bit router ID to uniquely identify a node in the network.
C. OSPFv3 routes are always preferred over OSPFv2 routes for all traffic.
D. OSPFv3 and OSPFv2 can be configured at the same time.
Answer: A, D

NO.16 Your are the administrator for a network that uses IS-IS as its IGP. As the network grows, you find that
the protocol's default capabilities for setting metrics is limiting your options. Which feature can you
implement to provide a larger range of metric configuration capabilities?
A. extended metrics
B. wide metrics
C. expanded metrics
D. full metrics
Answer: D

NO.17 You are provisioning a new customer for access to your Layer 3 VPN. The customer is using
172.16.35.0/24 as their internal IP address space, which is also being used by an existing Layer 3 VPN
customer. The two customers share many PE routers in common across your network. Which mechanism
allows these duplicate addresses to exist in your network?
A. route origin
B. route target
C. route refresh
D. route distinguisher
Answer: D

NO.18 You manage an MPLS network where the PE devices consist of multiple vendors.
You are asked to conceal the MPLS topology for all LSPs.
Which global configuration parameter will accomplish this?
A. Configure no-decrement-ttl on the ingress router only.
B. Configure no-propagate-ttl on the ingress router only.
C. Configure no-decrement-ttl on all routers within the MPLS network.
D. Configure no-propagate-ttl on all routers within the MPLS network.
Answer: D

NO.19 Click the Exhibit button.
On your MX Series router, traffic using the critical scheduler is out of profile. All other data is currently in
profile. Referring to the exhibit, which statement is correct?
A. The critical queue is serviced before the less-critical queue.
B. The critical queue is serviced after the left-over queue.
C. The critical queue is serviced before the data queue.
D. The critical queue is serviced before the voice queue.
Answer: B

NO.20 Which CoS feature supports per-VLAN queuing and scheduling?
A. multilevel scheduling
B. hierarchical scheduling
C. tagged queuing
D. per-instance queuing
Answer: C
Posted 2012/12/27 4:02:48  |  Category: 미분류  |  Tag: