Cisco 350-029 (CCIE SP Written Exam, V3.0) 인증시험공부자료는 Pass4Test에서 제공해드리는 Cisco 350-029 (CCIE SP Written Exam, V3.0) 덤프가 가장 좋은 선택입니다. Pass4Test에서는 시험문제가 업데이트되면 덤프도 업데이트 진행하도록 최선을 다하여 업데이트서비스를 제공해드려 고객님께서소유하신 덤프가 시장에서 가장 최신버전덤프로 되도록 보장하여 시험을 맞이할수 있게 도와드립니다.
NO.1 What is the typical marked DSCP value for a voice media packet in Voice
over IP technology?
A. AF41
B. AF31
C. AF21
D. BE
E.
EF
Answer: E
NO.2 Which two network management models are supported by
IPoDWDM? (Choose two.)
A. virtual transponder protocol management
B.
segmented management
C. integrated management
D. traffic management
E.
slow outages management
Answer: B,C
NO.3 Which statement about OSPF
authentication is true?
A. To enable OSPF authentication in a network, OSPF
area 0 authentication must be enabled first.
B. The payload of OSPFv3 packets
contains no authentication information.
C. OSPFv3 supports Advanced
Encryption Standard
D. OSPFv3 uses router ID as a key to encrypt OSPF hello
packets.
E. OSPF MD5 authentication uses TCP, and Plan Test authentication
uses UDP.
Answer: B
NO.4 Forwarding Equivalence Class (FEC)
corresponds to which four of these? (Choose four).
A. Layer 2 circuits (ATM,
FR, PPP, HDLC, Ethernet
B. Groups of addresses/sites-VPN
C. IPSEC
Encryption Algorithm
D. A bridge/switch instance-VSI
E. Tunnel
interface-traffic engineering
Answer: A,B,D,E
NO.5 Refer to the
exhibit.
R3 is not able to install the R1 loopback address into its BGP
routing table. What should be configured
to install that route?
A.
Configure R2 as a route reflector.
B. Enable EBGP multihop on R2.
C.
Change the origin attribute to IGP on R3.
D. Configure the next-hop-self
command on R2.
E. Configure the next-hop-unchanged command on R2.
F. Add a
static route to reach 10.10.23.2 on R3.
Answer: D
NO.6 Refer to the
exhibit.
Based on the topology, the BGP configuration in R1, and the outputs
from R1 and R2; identify why
was subnet 33.33.33.33/32 not received on the R2
BGP table?
A. R2 is not a route reflector client for R1.
B. R1 is
configured to suppress all inactive (RIB failure) routes.
C. The
33.33.33.33/32 subnet must be learned through BGP.
D. The 11.11.11.11/32
subnet exists in the routing table.
Answer: D
NO.7 An engineer is
looking into a solution for two customers that are using the network
prefix
10.10.1.0/24. The network engineer wants the network prefix to remain
the same for both
customers, while maintaining unique network information for
each. Which approach can be used to
achieve this requirement?
A. Assign a
unique RD per customer.
B. Assign a unique RT per customer.
C. Assign a
unique SOO per customer.
D. Assign a unique TE per customer.
Answer:
A
NO.8 Which three options are functions of the Cisco Service Control
Engine? (Choose three.)
A. intelligent inspection and control of IP
packets
B. application of session-level bandwidth shaping
C. provisioning
of access aggregation
D. per-subscriber bandwidth management
E.
Implementation of VPN services
Answer: A,B,D
over IP technology?
A. AF41
B. AF31
C. AF21
D. BE
E.
EF
Answer: E
NO.2 Which two network management models are supported by
IPoDWDM? (Choose two.)
A. virtual transponder protocol management
B.
segmented management
C. integrated management
D. traffic management
E.
slow outages management
Answer: B,C
NO.3 Which statement about OSPF
authentication is true?
A. To enable OSPF authentication in a network, OSPF
area 0 authentication must be enabled first.
B. The payload of OSPFv3 packets
contains no authentication information.
C. OSPFv3 supports Advanced
Encryption Standard
D. OSPFv3 uses router ID as a key to encrypt OSPF hello
packets.
E. OSPF MD5 authentication uses TCP, and Plan Test authentication
uses UDP.
Answer: B
NO.4 Forwarding Equivalence Class (FEC)
corresponds to which four of these? (Choose four).
A. Layer 2 circuits (ATM,
FR, PPP, HDLC, Ethernet
B. Groups of addresses/sites-VPN
C. IPSEC
Encryption Algorithm
D. A bridge/switch instance-VSI
E. Tunnel
interface-traffic engineering
Answer: A,B,D,E
NO.5 Refer to the
exhibit.
R3 is not able to install the R1 loopback address into its BGP
routing table. What should be configured
to install that route?
A.
Configure R2 as a route reflector.
B. Enable EBGP multihop on R2.
C.
Change the origin attribute to IGP on R3.
D. Configure the next-hop-self
command on R2.
E. Configure the next-hop-unchanged command on R2.
F. Add a
static route to reach 10.10.23.2 on R3.
Answer: D
NO.6 Refer to the
exhibit.
Based on the topology, the BGP configuration in R1, and the outputs
from R1 and R2; identify why
was subnet 33.33.33.33/32 not received on the R2
BGP table?
A. R2 is not a route reflector client for R1.
B. R1 is
configured to suppress all inactive (RIB failure) routes.
C. The
33.33.33.33/32 subnet must be learned through BGP.
D. The 11.11.11.11/32
subnet exists in the routing table.
Answer: D
NO.7 An engineer is
looking into a solution for two customers that are using the network
prefix
10.10.1.0/24. The network engineer wants the network prefix to remain
the same for both
customers, while maintaining unique network information for
each. Which approach can be used to
achieve this requirement?
A. Assign a
unique RD per customer.
B. Assign a unique RT per customer.
C. Assign a
unique SOO per customer.
D. Assign a unique TE per customer.
Answer:
A
NO.8 Which three options are functions of the Cisco Service Control
Engine? (Choose three.)
A. intelligent inspection and control of IP
packets
B. application of session-level bandwidth shaping
C. provisioning
of access aggregation
D. per-subscriber bandwidth management
E.
Implementation of VPN services
Answer: A,B,D