Pass4Test의 Cisco 640-911 (Introducing Cisco Data Center Networking)덤프는 몇십년간 IT업계에 종사한 전문가들이 Cisco 640-911 (Introducing Cisco Data Center Networking)실제 시험에 대비하여 제작한 시험준비 공부가이드입니다. Cisco 640-911 (Introducing Cisco Data Center Networking)덤프공부가이드로 시험준비공부를 하시면 시험패스가 쉬워집니다. 공부하는 시간도 적어지고 다른 공부자료에 투자하는 돈도 줄어듭니다. Pass4Test의 Cisco 640-911 (Introducing Cisco Data Center Networking)덤프는 Cisco 640-911 (Introducing Cisco Data Center Networking)시험패스의 특효약입니다.
NO.1 Which two features must be licensed on a Cisco Nexus 5548UP Switch? (Choose two.)
A. Virtual Port Channel
B. Fibre Channel
C. FabricPath
D. iSCSI
Answer: B,C
NO.2 What is the addressing format of IPv6?
A. 48-bit dotted decimal
B. 48-bit colon-delimited hexadecimal
C. 64-bit dotted decimal
D. 64-bit colon-delimited hexadecimal
E. 128-bit dotted decimal
F. 128-bit colon-delimited hexadecimal
Answer: F
NO.3 Which three IP addresses are examples of an RFC 1918 address? (Choose three.)
A. 172.16.3.1/24
B. 209.165.201.5/27
C. 209.165.200.225/27
D. 10.30.20.1/28
E. 192.168.200.50/24
Answer: A,D,E
NO.5 Ethernet 1/1 is assigned IP address 10.1.1.1 with subnet mask 255.255.255.0. Which
configuration is used to configure EIGRP on a Cisco Nexus 7000 switch?
A. feature eigrp ! interface Ethernet1/1 ip address 10.1.1.1 255.255.255.0 no shutdown ! router eigrp
1 network 10.1.1.0 0.0.0.255
B. feature eigrp ! router eigrp 1 autonomous-system 1 ! interface Ethernet1/1 ip address 10.1.1.1/24
ip router eigrp 1 no shutdown
C. router eigrp 1 autonomous-system 1 ! interface Ethernet1/1 ip address 10.1.1.1/24
ip router eigrp 1 no shutdown
D. feature eigrp ! interface Ethernet1/1 ip address 10.1.1.1/24 no shutdown ! router eigrp 1 network
10.1.1.0 0.0.0.255
Answer: B
NO.6 Which transport protocol requires a three-way handshake to establish a new connection?
A. ARP
B. UDP
C. IP
D. TCP
Answer: D
NO.7 Where does Cisco Nexus Operating System store the startup configuration file?
A. RAM
B. flash
C. bootflash
D. volatile
E. NVRAM
Answer: E
NO.8 What is the command sequence to force a Cisco Nexus 6000 switch to boot using the golden
BIOS image?
A. Press Ctrl-Shift-6 within 30 seconds of when power is supplied to the switch.
B. Press Ctrl-] within 2 seconds of when power is supplied to the switch.
C. Press Ctrl-] within 30 seconds of when power is supplied to the switch.
D. Press Ctrl-Shift-6 within 2 seconds of when power is supplied to the switch.
Answer: D