Pass4Test  Citrix Other Certification 1Y0-350 (Citrix NetScaler 10 Essentials and Networking)시험덤프 구매전 구매사이트에서 무료샘플을 다운받아 PDF버전 덤프내용을 우선 체험해보실수 있습니다. 무료샘플을 보시면 Pass4Test  Citrix Other Certification 1Y0-350 (Citrix NetScaler 10 Essentials and Networking)시험대비자료에 믿음이 갈것입니다.고객님의 이익을 보장해드리기 위하여 Pass4Test는 시험불합격시  Citrix Other Certification 1Y0-350 (Citrix NetScaler 10 Essentials and Networking)덤프비용전액환불을 무조건 약속합니다. Pass4Test의 도움으로 더욱 많은 분들이 멋진 IT전문가로 거듭나기를 바라는바입니다.

 

NO.1 Scenario: A network engineer created an IPv6 virtual server on the NetScaler. The virtual

server is using a service group with two IPv4 servers bound to it. When testing access to the virtual

server from a client configured with an IPv6 address, he is unable to connect.

What could be the reason for this issue?

A. The NetScaler is disabled for NAT.

B. IPv6 protocol translation is disabled.

C. An IPv6 address on the NetScaler is not bound to the correct VLAN.

D. The NetScaler does not have an INAT rule to convert IPv4 to IPv6 from the back-end servers.

Answer: B

 

NO.2 Scenario: For security reasons, the NSIP needs to be configured to only be accessible on

interface 0/1, which is VLAN 300.

The NSIP address is 10.110.4.254 and the subnet mask is 255.255.255.0.

How would the network engineer achieve this configuration?

A. set ns config -nsvlan 300 -ifnum 0/1

B. set ns ip 10.110.4.254 -gui ENABLED -vrID 300

C. add vlan 300 set ns ip 10.110.4.254 -mgmtAccess ENABLED

D. set ns config -IPAddress 10.110.4.254 -netmask 255.255.255.0

Answer: A

 

NO.3 A network engineer has configured two NetScaler MPX appliances as a high availability (HA)

pair.

What can the engineer configure to prevent failover if only a single interface fails?

A. FIS

B. PBR

C. SNMP

D. VMAC

Answer: A

 

NO.4 Why would an engineer want to specify a TCP Profile for a specific service group?

A. To enable use of features like SSL over TCP for that specific service group.

B. To adjust the TCP settings for traffic to and from that specific service group.

C. To use a specific SNIP for traffic to the back-end servers in that service group.

D. To enable features like use source IP , TCP keep alive and TCP buffering for a specific service group.

Answer: B

 

NO.5 A network engineer wants to optimize a published load balanced SSL virtual server for WAN

connection with long delay, high bandwidth with minimal packet drops.

What would the network engineer use to do this type of optimization for the SSL virtual server?

A. SSL policy

B. TCP profile

C. Compression policy

D. Priority queuing policy

Answer: B

 

NO.6 Scenario: A NetScaler engineer needs to enable access to some web servers running on an

IPv6-only network. The clients connecting the services are on an IPv4 network. The engineer has

already enabled IPv6 on the NetScaler.

What does the engineer need to do in order to provide access to the services on the IPv6 network?

A. Create an IPv6 tunnel and a IPv4 virtual server.

B. Configure an IPv6 VLAN and bind the required interface.

C. Create a IPv4 virtual server and bind the service group to it.

D. Create an IPv6 ACL and a IPv4 virtual server and bind the ACL to the virtual server.

Answer: C

 

NO.7 Scenario: The NetScaler has connections to a large number of VPNs. The network engineer

wants to minimize the number of ARP requests.

Which feature should the network engineer enable to minimize ARP requests?

A. TCP Buffering

B. Use Source IP

C. Edge Configuration

D. MAC based forwarding

Answer: D

 

NO.8 Scenario: The NetScaler is connected to two subnets. The NSIP is 10.2.9.12. The external SNIP

is 10.2.7.3. The MIP for internal access is 10.2.9.3. Web servers, authentication servers and time

servers are on the 10.2.10.0/ 24 network which is available through the

10.2.9.1 router. The external firewall has the 10.2.7.1 address. Traffic bound for Internet clients

should flow through the external firewall.

Which command should be used to set the default route?

A. add route 0.0.0.0 0.0.0.0 10.2.7.1

B. add route 0.0.0.0 0.0.0.0 10.2.9.1

C. add route 10.0.0.0 255.0.0.0 10.2.9.1

D. add route 10.0.0.0 255.0.0.0 10.2.7.1

Answer: A

 

NO.9 Scenario: An engineer executes the following commands:

add vlan 2 bind vlan 2 -ifnum 1 / 2 add ns ip 10.110.4.200 255.255.255.0 bind vlan 2 -IPAddress

10.110.4.200 255.255.255.0

What type of IP address has been added to the NetScaler?

A. VIP address

B. NSIP address

C. SNIP address

D. GSLB Site IP address

Answer: C

 

NO.10 Scenario: A NetScaler appliance currently has a manually configured channel containing four

interfaces; however, the engineer has been told that the NetScaler must now only use a single

interface for this network. The engineer removes the channel and immediately notices a decrease in

network performance.

How could the engineer resolve this issue?

A. Reset the unused interfaces

B. Disable the unused interfaces

C. Enable flow control on all interfaces

D. Disable HA monitoring on the three interfaces that are no longer required

Answer: B