IT인증,IT자격증,IT자격증시험,IT인증시험

http://www.pass4test.net/

IBM Certifed Systems Expert C4040-221 (AIX 7 Administration )최신버전덤프

IBM Certifed Systems Expert C4040-221 (AIX 7 Administration ) 시험을 패스하려면 품질좋은 시험대비 알맞춤 덤프가 있으면 훨씬 편해집니다.pass4test에서 최선을 다해 발췌한 IBM Certifed Systems Expert C4040-221 (AIX 7 Administration ) 시험자료는  IBM Certifed Systems Expert C4040-221 (AIX 7 Administration ) 실제시험에 대비하여 제작한 최고의 시험대비자료입니다.pass4test의 전문가들은 IT업계에 오래동안 종사하여 얻은 노하우로 시험패스에 가장 편한 시험자료를 연구하는데 많은 심혈을 기울였습니다.

 

NO.1 The following information has been reported in an AIX error log:
How can the administrator prevent the error from reoccurring?
A. Create a secondary dump device greater than 266MB
B. Increase primary dump device size greater than 266MB
C. Increase "/var" file system to ensure it has a minimum of 266MB free space
D. Increase "/var/adm/ras/livedump" file system to ensure it has a minimum of 266MB free space
Answer: C

NO.2 After performing a NIM rte install, the administrator noticed that not all filesets are at the
correct Technology Level (TL). What action will help the administrator determine why the
inconsistent fileset levels were installed?
A. On the NIM server, run an Ippchk to identify if the Software Vital Product Data is valid.
B. On the NIM client, run oslevel command against the TL to identify missing prerequisites.
C. Run instfix command on NIM client to determine what filesets are inconsistent.
D. On the NIM server run the NIM IsIpp command to indentify downlevel filesets contained in the
lpp_source.
Answer: D

NO.3 A host has a single virtual Ethernet adapter (ent0) configured with only a default PVID, and the
administrator is trying to determine why it cannot be used to reach any other system on the
network. He suspects that it may be caused by a problem in the VLAN configuration.
How would the administrator determine the VLAN for which the adapter was configured?
A. Use the command 'Isdev -I ent0' on the host to determine the port VLAN ID.
B. Use the command 'Isattr-EI ent0' on the host to determine the port VLAN ID.
C. Look on the HMC to determine which VLAN is configured for the adapter.
D. Examine the Shared Ethernet Adapter on the Virtual I/O Server to determine which VLAN the
adapter is using.
Answer: C

NO.4 What is the difference between deferred and concurrent firmware updates?
A. Deferred firmware can be applied concurrently but contains updates that affect the internal
program load path, which are not activated until the next time the server is shut down and restarted.
B. Concurrent firmware must be done on all LPARs in the frame at the same time. Deferred
firmware can be loaded on each LPAR at a different time and only becomes active when the LPAR is
shutdown and restarted.
C. Deferred firmware can only be applied during an outage to the managed system as it will
automatically shut the managed system down during its installation.
D. Concurrent firmware is only for minor fixes to the system mircocode while deferred firmware
contains major fixes to the service processor.
Answer: A

NO.5 What is a requirement for Live Partition Mobility?
A. The network and disk must be virtual.
B. The disk must be virtual and a Logical Host Ethernet Adapter (LHEA) for network.
C. The client partition must be connected to a SAN.
D. The client partition must be set up as a 'Mover Service Partition'.
Answer: A

NO.6 How can an administrator disable Role Based Access Control (RBAC) in a WPAR?
A. Run chattr -E -I sys0 -a enhanced_RBAC=false Reboot the WPAR
B. Run the RBAC wizard and deselect 'Enable RBAC Reboot the system
C. Run chdev -I mywpar -a enhanced_RBAC=false Reboot the Global Environment
D. Run chwpar -a RBAC=false Reboot the WPAR
Answer: C

NO.7 Which technology provides the maximum amount of usable storage and resilience for a
system with 6 physical volumes?
A. RAID 0
B. RAID 1
C. RAID 5
D. RAID 6
Answer: C

NO.8 An LPAR is configured with strict logical volume mirroring across two disks for resilience. The
administrator would like to ensure if one disk fails the volume group stays online. Which command
will ensure that the datavg volume group stays online?
A. varyonvg -n datavg
B. mirrorvg-Q-c 2 datavg
C. mklvcopy -e m -s y (each logical volume name) 2
D. chvg -Qn datavg
Answer: D

Posted 2014/3/13 15:01:09  |  Category: IBM  |  Tag: C4040-221최신버전덤프