Citrix Other Certification 1Y0-350인증시험을 패스하여 자격증을 취득한것은 IT업계에 진출성공했다는 이정표와 같습니다. 이 자격증을 취득하는것은 많은 IT인사들의 꿈입니다. 하지만  Citrix Other Certification 1Y0-350시험은 난이도가 높은 시험이라 도전할 엄두가 나지 않는다고 합니다. 도전도 해보지 않고 어려울거라고 포기하면 어떤 일에서나 포기가 빠르다고 생각됩니다. Pass4Test 에서는  Citrix Other Certification 1Y0-350시험에 대비한 Citrix Other Certification 1Y0-350덤프공부자료를 제공해드립니다. 이 덤프를 구매하여 공부하시면 그렇게 어려운 Citrix Other Certification 1Y0-350 시험도 쉬워집니다. 제일 적은 투자로 제일 큰 수확을 가져다 드리는Pass4Test 를 찾아주세요.

 

NO.1 Scenario: A NetScaler appliance currently has a manually configured channel containing four
interfaces; however, the engineer has been told that the NetScaler must now only use a single
interface for this network. The engineer removes the channel and immediately notices a decrease in
network performance.
How could the engineer resolve this issue?
A. Reset the unused interfaces
B. Disable the unused interfaces
C. Enable flow control on all interfaces
D. Disable HA monitoring on the three interfaces that are no longer required
Answer: B

NO.2 Scenario: For security reasons, the NSIP needs to be configured to only be accessible on
interface 0/1, which is VLAN 300.
The NSIP address is 10.110.4.254 and the subnet mask is 255.255.255.0.
How would the network engineer achieve this configuration?
A. set ns config -nsvlan 300 -ifnum 0/1
B. set ns ip 10.110.4.254 -gui ENABLED -vrID 300
C. add vlan 300 set ns ip 10.110.4.254 -mgmtAccess ENABLED
D. set ns config -IPAddress 10.110.4.254 -netmask 255.255.255.0
Answer: A

NO.3 Scenario: An engineer executes the following commands:
add vlan 2 bind vlan 2 -ifnum 1 / 2 add ns ip 10.110.4.200 255.255.255.0 bind vlan 2 -IPAddress
10.110.4.200 255.255.255.0
What type of IP address has been added to the NetScaler?
A. VIP address
B. NSIP address
C. SNIP address
D. GSLB Site IP address
Answer: C

NO.4 A network engineer has configured two NetScaler MPX appliances as a high availability (HA)
pair.
What can the engineer configure to prevent failover if only a single interface fails?
A. FIS
B. PBR
C. SNMP
D. VMAC
Answer: A

NO.5 Scenario: The NetScaler is connected to two subnets. The NSIP is 10.2.9.12. The external SNIP
is 10.2.7.3. The MIP for internal access is 10.2.9.3. Web servers, authentication servers and time
servers are on the 10.2.10.0/ 24 network which is available through the
10.2.9.1 router. The external firewall has the 10.2.7.1 address. Traffic bound for Internet clients
should flow through the external firewall.
Which command should be used to set the default route?
A. add route 0.0.0.0 0.0.0.0 10.2.7.1
B. add route 0.0.0.0 0.0.0.0 10.2.9.1
C. add route 10.0.0.0 255.0.0.0 10.2.9.1
D. add route 10.0.0.0 255.0.0.0 10.2.7.1
Answer: A

NO.6 A network engineer wants to optimize a published load balanced SSL virtual server for WAN
connection with long delay, high bandwidth with minimal packet drops.
What would the network engineer use to do this type of optimization for the SSL virtual server?
A. SSL policy
B. TCP profile
C. Compression policy
D. Priority queuing policy
Answer: B

NO.7 Why would an engineer want to specify a TCP Profile for a specific service group?
A. To enable use of features like SSL over TCP for that specific service group.
B. To adjust the TCP settings for traffic to and from that specific service group.
C. To use a specific SNIP for traffic to the back-end servers in that service group.
D. To enable features like use source IP , TCP keep alive and TCP buffering for a specific service group.
Answer: B

NO.8 Scenario: A network engineer created an IPv6 virtual server on the NetScaler. The virtual
server is using a service group with two IPv4 servers bound to it. When testing access to the virtual
server from a client configured with an IPv6 address, he is unable to connect.
What could be the reason for this issue?
A. The NetScaler is disabled for NAT.
B. IPv6 protocol translation is disabled.
C. An IPv6 address on the NetScaler is not bound to the correct VLAN.
D. The NetScaler does not have an INAT rule to convert IPv4 to IPv6 from the back-end servers.
Answer: B

NO.9 Scenario: A NetScaler engineer needs to enable access to some web servers running on an
IPv6-only network. The clients connecting the services are on an IPv4 network. The engineer has
already enabled IPv6 on the NetScaler.
What does the engineer need to do in order to provide access to the services on the IPv6 network?
A. Create an IPv6 tunnel and a IPv4 virtual server.
B. Configure an IPv6 VLAN and bind the required interface.
C. Create a IPv4 virtual server and bind the service group to it.
D. Create an IPv6 ACL and a IPv4 virtual server and bind the ACL to the virtual server.
Answer: C

NO.10 Scenario: The NetScaler has connections to a large number of VPNs. The network engineer
wants to minimize the number of ARP requests.
Which feature should the network engineer enable to minimize ARP requests?
A. TCP Buffering
B. Use Source IP
C. Edge Configuration
D. MAC based forwarding
Answer: D