Pass4Test에서 출시한 Cisco 200-105최신덤프만 있으면 학원다닐 필요없이 시험패스 가능합니다. Cisco 200-105최신덤프를 공부하여 시험에서 떨어지면 불합격성적표와 주문번호를 보내오시면 덤프비용을 환불해드립니다.구매전 데모를 받아 덤프문제를 체험해보세요. 데모도 pdf버전과 온라인버전으로 나뉘어져 있습니다.pdf버전과 온라인버전은 문제는 같은데 온라인버전은 pdf버전을 공부한후 실력테스트 가능한 프로그램입니다.
IT인증시험을 쉽게 취득하는 지름길은Pass4Test에 있습니다. Pass4Test의Cisco인증 200-125자격증시험로 시험준비를 시작하면 성공에 가까워집니다. Cisco인증 200-125자격증시험는 최신 시험문제 출제방향에 대비하여 제작된 예상문제와 기출문제의 모음자료입니다. Cisco인증 200-125자격증시험는 시험을 통과한 IT업계종사자분들이 검증해주신 세련된 공부자료입니다. Pass4Test의Cisco인증 200-125자격증시험를 공부하여 자격증을 땁시다.
시험 번호/코드: 200-105시험 이름: Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0)
당신이 구입하기 전에 시도, 100% 합격율 보장
100% 환불보장약속 200-105최신덤프
PDF 및 소프트웨어, 연구와 실천
시험 번호/코드: 200-125시험 이름: CCNA Cisco Certified Network Associate CCNA (v3.0)
당신이 구입하기 전에 시도, 100% 합격율 보장
100% 환불보장약속 200-125자격증시험
PDF 및 소프트웨어, 연구와 실천
Cisco 200-125자격증시험의 무료샘플을 원하신다면 우의 PDF Version Demo 버튼을 클릭하고 메일주소를 입력하시면 바로 다운받아Cisco 200-125자격증시험의 일부분 문제를 체험해 보실수 있습니다. Cisco 200-125자격증시험 덤프는 모든 시험문제유형을 포함하고 있어 적중율이 아주 높습니다. Cisco 200-125자격증시험로Cisco 200-125자격증시험패스 GO GO GO !
지난 몇년동안 IT산업의 지속적인 발전과 성장을 통해Cisco 인증200-105최신덤프은 IT인증시험중의 이정표로 되어 많은 인기를 누리고 있습니다. IT인증시험을Pass4Test덤프로 준비해야만 하는 이유는Pass4Test덤프는 IT업계전문가들이 실제시험문제를 연구하여 시험문제에 대비하여 예상문제를 제작했다는 점에 있습니다.
200-105 덤프무료샘플다운로드하기: http://www.pass4test.net/200-105.html
NO.1 What is the result of issuing the frame-relay map ip 192.168.1.2 202
broadcast command?
A. defines the source IP address that is used in all
broadcast packets on DCLI 202
B. defines the DLCI that is used for all
packets that are sent to the 192.168.1.2 IP address
C. defines the
destination IP address that is used in all broadcast packets on DCLI 202
D.
defines the DLCI on which packets from the 192.168.1.2 IP address are
received
Answer: B
Explanation:
Frame-relay map ip 192.168.1.2 202
command statically defines a mapping between a network layer
address and a
DLCI. The broadcast option allows multicast and broadcast packets to flow across
the
link. The command frame-relay map ip 192.168.1.2 202 broadcast means to
mapping the distal IP
192.168.1.2 202 to the local DLCI . When the
"broadcast" keyword is included, it turns Frame Relay
network as a broadcast
network, which can forward
broadcasts.
http://www.cisco.com/en/US/docs/ios/wan/command/reference/wan_f2.html#wp1012264
NO.2
Which parameter or parameters are used to calculate OSPF cost in Cisco
routers?
A. Bandwidth, MTU, Reliability, Delay, and Load
B. Bandwidth,
Delay, and MTU
C. Bandwidth
D. Bandwidth and Delay
Answer: C
200-105시험문제
Explanation:
http://www.cisco.com/en/US/tech/tk365/technologies_white_paper09186a0080094e9e.sht
ml#t6
OSPF Cost
The cost (also called metric) of an interface in OSPF is
an indication of the overhead required to send
packets across a certain
interface. The cost of an interface is inversely proportional to the
bandwidth
of that interface. A higher bandwidth indicates a lower
cost.
There is more overhead (higher cost) and time delays involved in
crossing a 56k serial line than
crossing a 10M Ethernet line. The formula
used to calculate the cost is: Cost= 10000 0000/bandwidth
in bps
For
example, it will cost 10 EXP8/10 EXP7 = 10 to cross a 10M Ethernet line and will
cost 10
EXP8/1544000 =64 to cross a T1 line. By default, the cost of an
interface is calculated based on the
bandwidth; you can force the cost of an
interface with the ip ospf cost <value> interface sub
configuration
mode command.
NO.3 Refer to the exhibit.
If the router R1 returns the
given output and has not had its router ID set manually, what address
will
EIGRP use as its router ID?
A. 192.168.10.2
B. 1.1.1.1
C.
172.16.4.1
D. 192.168.1.2
Answer: B
200-105자격증시험
Explanation:
The
router ID is selected according to the following rules: manual configuration
highest up/up
loopback highest up/up physical interface
---
NO.4
Which term describes a spanning-tree network that has all switch ports in either
the blocking or
fowarding state?
A. provisioned
B. redundant
C.
converged
D. spanned
Answer: C
Explanation:
Spanning Tree Protocol
convergence (Layer 2 convergence) happens when bridges and switches
have
transitioned to either the forwarding or blocking state. When layer 2 is
converged, root bridge is
elected and all port roles (Root, Designated and
Non-Designated) in all switches are selected.