Pass4Test 의 Cisco CCNP 300-115덤프는  Cisco CCNP 300-115시험에 도전장을 던진 분들이 신뢰할수 있는 든든한 길잡이 입니다. Cisco CCNP 300-115시험대비 덤프뿐만아니라 다른 IT인증시험에 대비한 덤프자료도 적중율이 끝내줍니다.Cisco CCNP 300-115시험이나 다른 IT인증자격증시험이나 Pass4Test제품을 사용해보세요.투자한 덤프비용보다 훨씬 큰 이득을 보실수 있을것입니다.

NO.1 Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access,
distribution and core switches) that provides LAN connectivity from user PCs to corporate servers.
The distribution switches are configured to use HSRP to provide a high availability solution.
DSW1 -primary device for VLAN 101 VLAN 102 and VLAN 105
DSW2 - primary device for VLAN 103 and VLAN 104
A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its
status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed.
Troubleshooting has identified several issues. Currently all interfaces are up. Using the running
configurations and show commands, you have been asked to investigate and respond to the
following question.
During routine maintenance, it became necessary to shut down the GigabitEthernet1/0/1 interface
on DSW1. All other interfaces were up. During this time, DSW1 remained the active device for the
VLAN 102 HSRP group. You have determined that there is an issue with the decrement value in the
track command for the VLAN 102 HSRP group. What needs to be done to make the group function
properly?
A. The decrement value on DSW1 should be greaterthan 5 and less than 15. 0
B. The decrement value on DSW1 should be greaterthan 9 and less than 15.
C. The decrement value on DSW1 should be greaterthan 11 and less than 19.
D. The decrement value on DSWTs should be greaterthan 190 and less than 200.
E. The decrement value on DSWTs should be greaterthan 195 and less than 205.
Answer: C

NO.2 Refer to the exhibit.
Which set of configurations will result in all ports on both switches successfully bundling into an
EtherChannel?
A. switch1 channel-group 1 mode active switch2 channel-group 1 mode auto
B. switch1 channel-group 1 mode desirable switch2 channel-group 1 mode passive
C. switch1 channel-group 1 mode on switch2 channel-group 1 mode auto
D. switch1 channel-group 1 mode desirable switch2 channel-group 1 mode auto
Answer: D

NO.3 Which VLAN range is eligible to be pruned when a network engineer enables VTP pruning on a
switch?
A. VLANs 1-1001
B. VLANs 1-4094
C. VLANs 2-1001
D. VLANs 2-4094
Answer: C

NO.4 A network engineer deployed a switch that operates the LAN base feature set and decides to
use the SDM VLAN template. The SDM template is causing the CPU of the switch to
spike during peak working hours. What is the root cause of this issue?
A. The VLAN receives additional frames from neighboring switches.
B. The SDM VLAN template causes the MAC address-table to overflow.
C. The VLAN template disables routing in hardware.
D. The switch needs to be rebooted before the SDM template takes effect.
Answer: C

NO.5 What does the command vlan dot1q tag native accomplish when configured under global
configuration?
A. All frames within the native VLAN are tagged, except when the native VLAN is set to 1.
B. It allows control traffic to pass using the non-default VLAN.
C. It removes the 4-byte dot1q tag from every frame that traverses the trunk interface(s).
D. Control traffic is tagged.
Answer: D

NO.6 A network engineer must improve bandwidth and resource utilization on the switches by
stopping the inefficient flooding of frames on trunk ports where the frames are not needed. Which
Cisco IOS feature can be used to achieve this task?
A. VTP pruning
B. access list
C. switchport trunk allowed VLAN
D. VLAN access-map
Answer: A

NO.7 Refer to the exhibit.
A network engineer investigates a recent network failure and notices that one of the interfaces on
the switch is still down. What is causing the line protocol on this interface to be shown as down?
A. There is a layer 1 physical issue.
B. There is a speed mismatch on the interface.
C. The interface is configured as the target of the SPAN session.
D. The interface is configured as the source of the SPAN session.
E. There is a duplex mismatch on the interface.
Answer: C

NO.8 A network engineer wants to ensure Layer 2 isolation of customer traffic using a private VLAN.
Which configuration must be made before the private VLAN is configured?
A. Disable VTP and manually assign VLANs.
B. Ensure all switches are configured as VTP server mode.
C. Configure VTP Transparent Mode.
D. Enable VTP version 3.
Answer: C