Pass4Test는 IT인증자격증을 취득하려는 IT업계 인사들의 검증으로 크나큰 인지도를 가지게 되었습니다. 믿고 애용해주신 분들께 감사의 인사를 드립니다.Network Appliance NCIE-SAN NS0-504덤프도 다른 과목 덤프자료처럼 적중율 좋고 통과율이 장난이 아닙니다.Network Appliance NCIE-SAN NS0-504 덤프를 구매하시면 퍼펙트한 구매후 서비스까지 제공해드려 고객님이 보유한 덤프가 항상 시장에서 가장 최신버전임을 약속해드립니다. Network Appliance NCIE-SAN NS0-504덤프만 구매하신다면 자격증 취득이 쉬워져 고객님의 밝은 미래를 예약한것과 같습니다.
NO.1 You are booting a NetApp storage system for the first time. In which order
should the various
components be powered on?
A. any tape backup devices,
disk shelves, network switches, NetApp controller heads
B. NetApp controller
heads, disk shelves, any tape backup devices, network switches
C. NetApp
controller heads, disk shelves, network switches, any tape backup devices
D.
network switches, disk shelves, any tape backup devices, NetApp controller
heads
Answer: D
NO.2 A solution is setup with a Volume Guarantee =
volume, LUN reservation = off, Fractional
Reserve = 0%, Snap Reserve = 0%,
auto_delete = volume, auto_grow = on, try_first = autosize. Which
of these
choices best describes the use of these settings for our Space Policy?
A.
when you want to set aside overwrite reserve space for the LUNs so that writes
never fail with the
presence of Snapshots
B. when you want to use thinly
provisioned LUNs to overcommit the volume and increase
storage
efficiency
C. when you want Data ONTAP to start deleting Snapshots
to recover space from the volume before
growing the volume
D. when you
want to guarantee space for Snapshots by letting the volume autogrow
Answer:
D
Reference:http://blog.scottlowe.org/2007/12/05/managing-lun-space-requirements-withnetapp-
storage/
NO.3
When will a Volume SnapMirror (VSM) from a 64-bit source to a 32-bit destination
volume fail?
A. When the 64-bit volumes has Volume Guarantee disabled
B.
When the 64-bit volume has compression enabled
C. When the 64-bit volume has
FlexShare enabled
D. When the 64-bit volume has ASIS enabled
Answer:
B
Explanation:
Data compression is supported only on FlexVol volumes in
64-bit aggregates and not on volumes in
32-bitaggregates.
NO.4 Which
native GUI switch tool is used to manage Cisco MDS-Series switches and
directors?
A. Operations Manager
B. Fabric Manager
C. Web Tools
D.
Data Fabric Manager
Answer: B
NO.5 Click the Exhibit button.
A
Solaris 10 host with VERITAS Storage Foundation 4.1 is FCP attached to a FAS3140
high availability
storage system running single image cfmode. Using the
diagram shown, which ports will be
considered active by VERITAS DMP using the
NetApp ASL to a LUN on controller 1 mapped to host 1?
A. Port 0b on
controller 1 only
B. Port 0d on controller 1 only
C. Port 0b and 0d on
controller 1 only
D. Ports 0b and 0d on both controller 1 and controller
2
Answer: A
NO.6 The largest volume that can be created on a 64-bit
aggregate is ___.
A. 10 TB
B. 16 TB
C. 64 TB
D. Equal to size of the
aggregate
Answer: D
NO.7 A company wants to use jumbo frames in their
Ethernet network. They should set the packet
size to which industry
conventional value?
A. 1200
B. 1500
C. 9000
D. 12000
Answer:
C
NO.8 The storage administrator has verified SAN fabric connectivity
between the initiator and target
other LUNs are visible. However, one LUN
still is NOT visible to the initiator. What do you need to do
to determine
the cause?
A. verify the target HBA is enabled
B. verify the LUN is
properly mapped to a correct igroup
C. verify the initiator HBA is
enabled
D. verify the LUN has been configured to the appropriate OS
type
Answer: B
should the various
components be powered on?
A. any tape backup devices,
disk shelves, network switches, NetApp controller heads
B. NetApp controller
heads, disk shelves, any tape backup devices, network switches
C. NetApp
controller heads, disk shelves, network switches, any tape backup devices
D.
network switches, disk shelves, any tape backup devices, NetApp controller
heads
Answer: D
NO.2 A solution is setup with a Volume Guarantee =
volume, LUN reservation = off, Fractional
Reserve = 0%, Snap Reserve = 0%,
auto_delete = volume, auto_grow = on, try_first = autosize. Which
of these
choices best describes the use of these settings for our Space Policy?
A.
when you want to set aside overwrite reserve space for the LUNs so that writes
never fail with the
presence of Snapshots
B. when you want to use thinly
provisioned LUNs to overcommit the volume and increase
storage
efficiency
C. when you want Data ONTAP to start deleting Snapshots
to recover space from the volume before
growing the volume
D. when you
want to guarantee space for Snapshots by letting the volume autogrow
Answer:
D
Reference:http://blog.scottlowe.org/2007/12/05/managing-lun-space-requirements-withnetapp-
storage/
NO.3
When will a Volume SnapMirror (VSM) from a 64-bit source to a 32-bit destination
volume fail?
A. When the 64-bit volumes has Volume Guarantee disabled
B.
When the 64-bit volume has compression enabled
C. When the 64-bit volume has
FlexShare enabled
D. When the 64-bit volume has ASIS enabled
Answer:
B
Explanation:
Data compression is supported only on FlexVol volumes in
64-bit aggregates and not on volumes in
32-bitaggregates.
NO.4 Which
native GUI switch tool is used to manage Cisco MDS-Series switches and
directors?
A. Operations Manager
B. Fabric Manager
C. Web Tools
D.
Data Fabric Manager
Answer: B
NO.5 Click the Exhibit button.
A
Solaris 10 host with VERITAS Storage Foundation 4.1 is FCP attached to a FAS3140
high availability
storage system running single image cfmode. Using the
diagram shown, which ports will be
considered active by VERITAS DMP using the
NetApp ASL to a LUN on controller 1 mapped to host 1?
A. Port 0b on
controller 1 only
B. Port 0d on controller 1 only
C. Port 0b and 0d on
controller 1 only
D. Ports 0b and 0d on both controller 1 and controller
2
Answer: A
NO.6 The largest volume that can be created on a 64-bit
aggregate is ___.
A. 10 TB
B. 16 TB
C. 64 TB
D. Equal to size of the
aggregate
Answer: D
NO.7 A company wants to use jumbo frames in their
Ethernet network. They should set the packet
size to which industry
conventional value?
A. 1200
B. 1500
C. 9000
D. 12000
Answer:
C
NO.8 The storage administrator has verified SAN fabric connectivity
between the initiator and target
other LUNs are visible. However, one LUN
still is NOT visible to the initiator. What do you need to do
to determine
the cause?
A. verify the target HBA is enabled
B. verify the LUN is
properly mapped to a correct igroup
C. verify the initiator HBA is
enabled
D. verify the LUN has been configured to the appropriate OS
type
Answer: B