제일 간단한 방법으로 가장 어려운 문제를 해결해드리는것이 Pass4Test의 취지입니다.Cisco 648-375 (Cisco Express Foundation for Systems Engineers (CXFS) Exam) 시험은 가장 어려운 문제이고 Pass4Test의 Cisco 648-375 (Cisco Express Foundation for Systems Engineers (CXFS) Exam) 덤프는 어려운 문제를 해결할수 있는 제일 간단한 공부방법입니다. Pass4Test의 Cisco 648-375 (Cisco Expre ss Foundation for Systems Engineers (CXFS) Exam) 덤프로 시험준비를 하시면 아무리 어려운 Cisco 648-375 (Cisco Express Foun dation for Systems Engineers (CXFS) Exam) 시험도 쉬워집니다.
NO.1 What should you keep in mind when using a midspan PSE?
A. It can be used to deliver PoE over 100BASE-T connections
B. It can implement power delivery only over the spare wires of the copper cabling
C. It defines terminology to describe a port that acts as a PSE to a powered device
D. It states that power can be delivered by an end-point PSE
Answer: B
NO.2 You are working with a company that has an infrastructure based on lightweight access points
using the advanced feature set. A new security requirement demands real-time asset tracking for
800 assets. Which product or solution will provide this function?
A. Wireless Control System
B. Wireless Location Appliance
C. Wireless LAN Solution Engine
D. Wireless LAN Services Module
Answer: B
NO.3 Which VMS Security Monitor tool allows you to monitor data for patterns of attacks from one
machine to a list of targets?
A. Advanced Correlation Engine
B. Management Center for CSA
C. CiscoWorks Dashboard
D. Advanced Notification Engine
Answer: A
NO.4 What should you keep in mind when working with antennas?
A. Antennas can be used as transmit and receive antennas on the same radio
B. All antennas broadcast the horizontal plane
C. Isotropic antennas broadcast equally in all directions
D. An antennas that converts electrical energy into RF waves is called a receive antenna
Answer: C
NO.5 What is the purpose of the Dynamic Configuration Tool?
A. to allow for the mass deployment of devices with minimal configurations
B. to provide an easy way to check for known bugs in IOS releases
C. to determine the correct IOS image to support your modules or blades
D. to test router configurations virtually prior to implementing them in your production network
E. to verify that hardware such as modules are compatible with your chassis
Answer: E
NO.6 Which of these is a benefit of an integrated security management system?
A. It provides configuration, monitoring, and troubleshooting capabilities across a wide range of
security products.
B. It leverages existing network management systems such as HP OpenView to lower the cost of
implementation.
C. It integrates security management capabilities into the router or switch.
D. It integrates security device management products and collects events on an "as needed" basis
to reduce management overhead.
E. It provides a single point of contact for all security configuration tasks thereby enhancing the
return on investment.
Answer: A
NO.7 In the plan phase, network readiness assessment addresses the optimal technologies for
supporting its business requirements and objectives
A. TRUE
B. FALSE
Answer: B
NO.8 What are two of the four key benefits of the ISR platforms? (Choose two)
A. monitoring, analysis, and response
B. investment protection
C. guest access
D. voice and mobility ready
E. storage virtualization
Answer: B,D
NO.9 Which of these is an accurate list of Cisco Lifecycle Services phases?
A. project planning, site assessment, risk assessment, solution selection and acquisition, testing,
and operations
B. analysis, design, deployment, testing, implementation, and production
C. prepare, plan, design, implement, operate, and optimize
D. initiation, planning, analysis, design, development, implementation, operations and
maintenance
E. presales, project planning, development, implementation, operations testing, and operations
sign-off
Answer: C
NO.10 What should you do to prevent VLAN hopping?
A. Enable all unused ports and place them into an unused VLAN
B. Set unused access ports to trunking ON
C. Disable some unused ports
D. Disable all unused ports and place them into an unused VLAN
Answer: D