현재 많은 IT인사들이 같은 생각을 하고 있습니다. 그것은 바로   Cisco Specialist 642-995 (Unifi ed Computing Troubleshoot) 인증시험 자격증 취득으로 하여 IT업계의 아주 중요한 한걸음을 내딛이는 것입니다.그만큼   Cisco Specialist 642-995 (Unified Computing Troubleshoot) 인증시험의 인기는 말 그대로 하늘을 찌르고 있습니다.Pass4Test는 많은 IT인사들이   Cisco Specialist 642-995 (Unified Computing Troubleshoot) 인증시험에 참가하는데 완벽한   Cisco Specialist 642-995 (Unified Computing Troubleshoot) 인증시험자료를 제공해드려 여러분들이 안전하게   Cisco Specialist 642-995 (Unified Computing Troubleshoot) 인증시험 자격증을 취득하게 하는 사이트입니다. Pass4Test의 자료들은 모두 Pass4Test의 전문가들의 연구와 노력 끝에  퍼펙트하게 만들어진 것입니다.우리 덤프들은 최고의 품질을 보장하며 업데이트스피드 또한 아주 빠릅니다.우리의 덤프는 모두 실제시험을 커버하여 최고의 적중율을 약속합니다.Pass4Test의 제품은 고난이도인   Cisco Specialist 642-995 (Unified Computing Troubleshoot) 시험을 한방에 패스하는데 도움드려 여러분의 사업에 많은 이익이 되어드립니다.Pass4Test가 제공하는 제품을 사용함으로 여러분은 IT업계 하이클래스와 멀지 않았습니다.Pass4Test 가 제공하는 인증시험 덤프는 여러분이  Cisco Specialist 642-995 (Unified Computing Troubleshoot) 시험을 안전하게 통과하는데는  물론 관연 전업 지식 장악에도 많은 도움을 드립니다.

 

 

NO.1 Which command can be run on an upsteam Cisco MDS switch to determine if a virtual Fibre Channel
interface has successfully logged into the fabric?
A. show zoneset active
B. show fcdomain domain-list
C. show vsan database
D. show npiv status
Answer: A

NO.2 By default, how long are cleared faults retained in the fault log?
A. 10 minutes
B. 1 hour
C. 3 minutes
D. 24 hours
Answer: B

NO.3 Which tool can be used to view server temperature sensors?
A. SoL
B. dmidecode
C. IPMI
D. SPAN
Answer: C

NO.4 A chassis has all four I/O module ports connected but only one is being used. Which action will establish
full functionality to all four ports?
A. Enable the connecting ports on the upstream fabric interconnect.
B. Reacknowledge the chassis.
C. Reboot the affected servers.
D. Disable and re-enable the I/O module ports.
Answer: B

NO.5 During an attempted SAN boot, ROM BIOS fails and reports failure to find the configured LUN. Which
is the mostly likely cause?
A. The service profile has incorrectly configured Ethernet interfaces.
B. The service profile has incorrect LUN ID.
C. The Cisco UCS cluster is in NPV mode rather than switch mode.
D. The Cisco UCS cluster is in EHV mode rather than switch mode.
Answer: B

NO.6 Which policy type can be configured to monitor motherboard temperature?
A. threshold policies
B. maintenance policies
C. power control policies
D. BIOS policies
Answer: A

NO.7 After a memory upgrade, a customer ¯ s se r ve r f a il s t o boo t. W h i ch o f t he f o ll o w i ng cou l d cause a se r ve r
to be unable to boot?
A. a correctable ECC DIMM error
B. a non-correctable ECC DIMM error
C. a correctable ECC DIMM error that exceeds the error rate threshold
D. a degraded DIMM
Answer: B

NO.8 What is the over-subscription ratio of a fully populated Cisco UCS 5108 chassis with four fabric
connections per I/O module?
A. 1:1
B. 2:1
C. 3:1
D. 4:1
Answer: B

NO.9 What information is recorded in the system event log?
A. split-brain status
B. VLAN membership
C. over- and under-voltage
D. high-availability status
Answer: C

NO.10 In order to perform a SAN boot, which entry should be located in the FCNS database?
A. Initiator
B. Target
C. Any E Ports in the data path
D. Both the Initiator and the Target
Answer: D

NO.11 In a fully provisioned Cisco UCS 5108 chassis, how many fan modules are present?
A. 2
B. 4
C. 6
D. 8
Answer: D

NO.12 Which operation is most likely to cause the corruption of an I/O module?
A. improper firmware upgrade
B. improper transition to EHV mode
C. improper transition to Fibre Channel switch mode
D. FULL state backup
Answer: A

NO.13 Which command displays the transport (Ethernet, Fibre Channel) used by a virtual interface?
A. show fex detail
B. show service-profile circuit server x/y
C. show pinning server-interface
D. show pinning border-interface
Answer: B

NO.14 After connecting to an M71KR server adapter, which command displays the adapter ¯ s v if s WW N s?
A. show server-profile circuit server
B. show-vifs
C. show interface
D. show fex detail
Answer: B

NO.15 A Cisco UCS cluster has two four-link I/O module connections to a single chassis. Server 8 is
provisioned with an M72-KR mezzanine card, which is pinned to I/O module Port 4. If I/O module Port 4
fails, what happens to the Ethernet traffic flow that is transmitted by Server 8.?
A. The traffic flow fails over to the second fabric interconnect.
B. The traffic flow stops until an administrator takes corrective action.
C. The traffic will be re-pinned to a different port on the same I/O module.
D. The traffic will utilize the cluster ports to flow between the initiator and the target.
Answer: B