IT업계 종사자라면 누구나  CCA 1Y0-A26 (Citrix XenServer 6.0 Administration)시험을 패스하고 싶어하리라고 믿습니다. 많은 분들이 이렇게 좋은 인증시험은 아주 어렵다고 생각합니다. 네 맞습니다. 패스할 확율은 아주 낮습니다. 노력하지 않고야 당연히 불가능한 일이 아니겠습니까? CCA 1Y0-A26 (Citrix XenServer 6.0 Administration) 시험은 기초 지식 그리고 능숙한 전업지식이 필요 합니다. Pass4Test는 여러분들한테 CCA 1Y0-A26 (Citrix XenServer 6.0 Administration)시험을 쉽게 빨리 패스할 수 있도록 도와주는 사이트입니다.Pass4Test 의  CC A 1Y0-A26 (Citrix XenServer 6.0 Administration)시험관련 자료로 여러분은 짧은 시간내에 간단하게 시험을 패스할수 있습니다. 시간도 절약하고 돈도 적게 들이는 이런 제안은 여러분들한테 딱 좋은 해결책이라고 봅니다.Pass4Test 에서 제공하는 학습가이드에는 IT전문가들이 만들어낸  CCA 1Y0-A26 (Citrix XenServer 6.0 Administration) 인증시험의 완벽한 문제와 답들을 대비한 자료가 포함되어있습니다. Pass4Test에서는 IT업계에서의 높은 신뢰감으로 여러분들한테 100%보장을 드립니다.  믿음을 드리기 위하여  CCA 1Y0-A26 (Citrix XenServer 6.0 Administration)관련자료의 일부분 문제와 답 등 샘플을 무료로 다운받아 체험해 볼수 있게 제공합니다. CCA 1Y0-A26 (Citrix XenServer 6.0 Administration) 문제와 답을 체험하는 동시에 Pass4Test 제품 선택여부에 대하여 답이 나올 것입니다.Pass4Test 는 백프로 여러분들한테 편리함과 통과율을 보장 드립니다. 여러분이 안전하게  CCA 1Y0-A26 (Citrix XenServer 6.0 Administration)시험을 패스할 수 있는 곳은 바로 Pass4Test입니다.인증시험을 패스하려면 시험대비 자료 선택은 필수입니다. Pass4Test의 전문가들은 모두 경험도 많고, 그들이 연구해낸 자료는 실제시험의 문제를 많이 적중하고 있습니다.

 

 

NO.1 Scenario: An administrator notices a duplex mismatch on the network interface card (NIC) which is
configured as the management interface. The administrator realizes that the switch was set to 100 full,
but XenServer auto-configured the NIC to 100 half, autoneg=on. How can the administrator ensure the
XenServer host does NOT auto-configure the NIC in the future?
A. Change the NIC properties in the xsconsole.
B. Use the xe pif-configure-ip command to disable auto-configuration.
C. Use the xe pif-param-set command to set other-config:ethtool-autoneg=off.
D. Assign a new NIC to the management interface within the XenCenter Network tab.
Answer: C

NO.2 Scenario: An administrator needs to upgrade the memory of a XenServer host. Business requirements
state that this task can only be done during business hours. Which two steps must the administrator take
before shutting down a XenServer host in an environment that has high availability enabled without
affecting performance? (Choose two.)
A. Disable the host.
B. Evacuate the host.
C. Reset the pool master.
D. Disable high availability.
Answer: AB

NO.3 An administrator cloned a template into a virtual machine and then converted it back into a template.
Which action must be performed on the disks to restore expected levels of disk performance?
A. Run SysPrep
B. Complete a full copy
C. Execute a fast clone
D. Suspend before cloning
Answer: B

NO.4 An administrator needs to apply an update to a XenServer pool, but needs to control the update path
and the virtual machine migration. What does the administrator need to do to achieve this?
A. Update all hosts in the pool using the xe CLI.
B. Use the Install Update wizard to update the pool.
C. Update each host individually starting with the pool master.
D. Select manual update mode when updating the pool in XenCenter.
Answer: C

NO.5 An administrator was given new security rules and now needs to remove specific permissions from the
users in the VM Admin Role Based Access Control group. How can the administrator remove the specific
permissions from the VM Admin user group?
A. Reset the VM Admin user group back to the default permissions.
B. Delete the registry key that applies to the specific permissions that need to be removed.
C. Run the xe subject-role-remove uuid=<subject UUID> role-name=vm.pool_migrate XenServer
command.
D. Remove the specific permissions from the Active Directory user group associated with the VM Admin
user group.
Answer: C

NO.6 Scenario: In an environment with high availability enabled, an administrator discovered that a host is
unreachable in a XenServer pool. The administrator disabled high availability in order to make the host
reachable. Which xe CLI command can the administrator run to make the host reachable again?
A. host-disable
B. host-evacuate
C. pool-designate-new-master
D. pool-emergency-reset-master
Answer: D

NO.7 An administrator is planning to apply an update that has already been downloaded to a XenServer host
in production. What is the next step that the administrator needs to take in the update process?
A. Restart the host.
B. Generate the UUID for the patch.
C. Specify the UUIDs of the host and the patch.
D. Shut down, suspend or migrate the virtual machines running on the host.
Answer: D

NO.8 Scenario: An administrator configured XenServer Role Based Access Control (RBAC) to authenticate
using Active Directory. Using RBAC, the administrator must grant Level 2 Support users with permission
to start and stop virtual machines. Which two steps must the administrator take to grant Level 2 Support
users virtual machine permissions? (Choose two.)
A. Assign a role to the subject.
B. Add an Active Directory group to the pool.
C. Assign XenServer permissions to a group.
D. Add users and their roles to the authorized list of users.
Answer: AB

NO.9 An administrator is setting up the XenServer hosts in an environment to boot from SAN. In which BIOS
would the administrator go to enable XenServer to boot from SAN.?
A. Host
B. Array controller
C. Network interface card
D. Primary host bus adapter
Answer: D

NO.10 When starting up a XenServer from SAN, the BIOS of the ___________ contains the instructions that
enable the host to find the boot disk. (Choose the correct option to complete the sentence.)
A. host machine
B. array controller
C. host bus adapter
D. network interface card
Answer: C

NO.11 Scenario: An administrator is planning to introduce 100 new virtual machines into the environment.
The administrator plans to use XenServer templates and duplication mechanisms. What must the
administrator consider when deciding between the full copy and fast clone duplication mechanisms?
A. A template needs to be copied before it can be fast cloned.
B. A virtual machine that is duplicated using the full copy method may impact disk performance.
C. A virtual machine that is duplicated using the fast cloned method may impact disk performance.
D. A template created on local storage can be duplicated by using the full copy method by any host in the
pool.
Answer: C

NO.12 Scenario: To improve performance and increase security, a network team will be moving all XenServer
hosts into a more secure, and high resiliency subnet. The administrator must now change the subnet
mask on all XenServer hosts to match the new network: 172.16.0.0/16. Which command will the
administrator need to execute on each host?
A. xe pif-reconfigure-ip uuid= mode=dhcp netmask=255.255.0.0
B. xe pif-reconfigure-ip uuid= mode=static netmask=255.255.0.0
C. xe pif-reconfigure-ip uuid= mode=dhcp netmask=172.16.0.0/16
D. xe pif-reconfigure-ip uuid= mode=static netmask=172.16.0.0/16
Answer: B

NO.13 An administrator needs to run commands to specify __________ to configure email alerts at the host
level. (Choose the correct option to complete the sentence.)
A. alarm_priority on the host
B. alarm_priority on the virtual machine
C. the sender email address and SMTP server
D. the recipient email address and SMTP server
Answer: D

NO.14 An administrator needs to export a virtual machine to an NFS share mounted on a XenServer host.
Which xe CLI command does the administrator need to execute from a remote machine to perform the
virtual machine export?
A. xe vm-export -h <hostname> filename=<pathname_of_file>
B. xe vm-export -h <hostname> -u <root> -pw <password> vm=<vm_name>
C. xe vm-export -h <hostname> -u <root> -pw <password> filename=<pathname_of_file>
D. xe vm-export -h <hostname> -u <root> -pw <password> vm=<vm_name>
filename=<pathname_of_file>
Answer: D

NO.15 Scenario: An administrator is moving a XenServer host from the New York datacenter to the London
datacenter. During the installation of XenServer, the default NTP settings were selected. How must the
administrator ensure that the XenServer host has the correct time settings?
A. Configure the time in the host BIOS.
B. Configure the time zone in the ntp.conf file.
C. Change the time zone using the xsconsole.
D. Change the NTP servers to the London NTP servers.
Answer: C

NO.16 Scenario: An administrator is unable to connect to a resource pool in a XenServer environment in
which high availability is enabled. The administrator discovers that the host is unreachable. What does
the administrator need to do to recover the host?
A. Run the pool-disable command, then the host-shutdown command and then restart the host.
B. Run the pool-disable command, then run the pool-emergency-reset-master command and restart the
host.
C. Run the emergency-ha-disable command, then once the host is restarted, run the pool-ha-enable
command.
D. Run the host-evacuate command, then restart the host and run the pool-emergency-transition-to-
master command.
Answer: C

NO.17 Scenario: An administrator is planning to upgrade the RAM in a XenServer host. Due to business
restrictions, the host must be shut down during normal business hours. High availability is enabled in the
XenServer resource pool. Which step does the administrator need to take before shutting down the
XenServer host to allow the virtual machines to run after the host is shut down?
A. Disable high availability.
B. Export the virtual machines.
C. Place the host in maintenance mode.
D. Copy the virtual machines to another host.
Answer: C

NO.18 An administrator needs to authenticate all users when they log into the XenServer pool using their
Windows credentials. What is the first step the administrator must take to achieve this?
A. Join the XenServer pool to the domain.
B. Add each user to the Users tab in XenCenter.
C. Create a XenServer user group within Active Directory.
D. Create Active Directory accounts for the XenServer users.
Answer: A

NO.19 Scenario: An administrator is adding a new host to a XenServer resource pool. XenServer is already
installed on the host, but the NTP server settings are configured incorrectly on the host. Which file can the
administrator edit to adjust the NTP server settings on the new XenServer host?
A. /etc/ntp.conf
B. /etc/ntp/keys
C. /etc/init.d/ntpd
D. /etc/ntp/step-tickers
Answer: A

NO.20 What must be true in order to integrate Active Directory authentication with a XenServer host?
A. LDAP port 389 is open for inbound traffic to the XenServer host.
B. The Active Directory administrator account is created locally on the XenServer host.
C. The same DNS server is used for both the Active Directory server and the XenServer host.
D. RAS authentication is used for communication between the Active Directory server and the XenServer
host.
Answer: C