IT인증,IT자격증,IT자격증시험,IT인증시험

http://www.pass4test.net/

Cisco 350-001 (CCIE Cisco Certified InterNetworking Expert) 덤프공부

Pass4Test는 IT업계 전문가들이 그들의 노하우와 몇 년간의 경험 등으로 자료의 정확도를 높여 응시자들의 요구를 만족시켜 드립니다.  Pass4Test 는 꼭 한번에  Cisco 350-001 (CCIE Cisco Certified InterNetworking Expert)  시험을 패스할 수 있도록 도와드릴 것입니다. 여러분은  Cisco 350-001 (CCIE Cisco Certified InterNetworking Expert) 시험자료 구매로 제일 정확하고 또 최신 시험 문제에 대비한 학습가이드를 사용할 수 있습니다. Pass4Test의 인증시험 적중율은 아주 높습니다. 때문에 많은 IT인증시험 준비중인 분들에게 많은 편리를 드릴수 있습니다.100%정확도 100%신뢰! 여러분은 마음 편히 응시하시면 됩니다.Pass4Test는 여러분의 시간을 절약해드릴 뿐만 아니라 여러분들이 안심하고 응시하여 순조로이 패스할수 있도록 도와주는 사이트 입니다. Pass4Test는 믿을 수 있는 사이트입니다. IT업계에서는 이미 많이 알려져 있습니다. 그리고 여러분에 신뢰를 드리기 위하여  Cisco 350-001 (CCIE Cisco Certified InterNetworking Expert)  관련자료의 일부분 문제와 답 등 샘플을 무료로 다운받아 체험해볼 수 있게 제공합니다. 아주 만족할 것이라고 믿습니다.  Pass4Test제품에 대하여 아주 자신이 있습니다. Cisco 350-001 (CCIE Cisco Certified InterNetworking Expert) 도 여러분의 무용지물이 아닌 아주 중요한 자료가 되리라 믿습니다. 여러분께서는 아주 순조로이 시험을 패스하실 수 있을 것입니다.

 

 

NO.1 Refer to the exhibit.
Which switching feature is being tested?
A. loop guard
B. PortFast
C. root guard
D. BDPU guard
Answer: A

NO.2 What two features in Cisco switches help prevent Layer 2 loops? (Choose two)
A. UniDirectional Link Detection
B. Hot Standby Router Protocol
C. Virtual Router Redundancy Protocol
D. PortFast
E. Root guard
F. Loop guard
Answer: AF

NO.3 Which standard supports multiple instances of spanning tree?
A. 802.1D
B. 802.1s
C. 802.1w
D. 802.1z
Answer: B

NO.4 Refer to the exhibit.
In the diagram, the switches are running IEEE 802.1w RSPT.
On which ports should root guard be enabled in order to facilitate deterministic root bridge election under
normal and failure scenarios?
A. GE-3/1, GE-3/2
B. FE-2/1, FE-3/2
C. GE-1/1.GE-1/2
D. GE-4/1, GE-4/2
E. GE-2/1, GE-2/2
F. GE-3/1, GE-3/2, GE-4/1, GE-4/2, FE-2/1, FE-3/2
Answer: F

NO.5 Prior to 802.1w, Cisco implemented a number of proprietary enhancements to 802.1D to improve
convergence in a Layer 2 network. Which statement is correct?
A. Only UplinkFast and BackboneFast are specified in 802.1w; PortFast must be manually configured.
B. Only PortFast is specified in 802.1w; UplinkFast and BackboneFast must be manually configured.
C. None of the proprietary Cisco enhancements are specified in 802.1w.
D. PortFast, UplinkFast, and BackboneFast are specified in 802.1w.
Answer: D

NO.6 Which two of these are used in the selection of a root bridge in a network utilizing Spanning Tree
Protocol IEEE 802.1D.? (Choose two)
A. Designated Root Cost
B. bridge ID priority
C. max age
D. bridge ID MAC address
E. Designated Root Priority
F. forward delay
Answer: BD

NO.7 Under which two circumstances would an RSTP bridge flush its CAM table? (Choose two)
A. Upon a port state change
B. Upon receiving a topology change notification
C. When transitioning from discarding to forwarding
D. When transitioning from forwarding to discarding
E. Only when changing from listening to discarding
F. When CAM resources have been completely used up
Answer: BC

NO.8 Spanning Tree Protocol IEEE 802.1s defines the ability to deploy which of these?
A. one global STP instance for all VLANs
B. one STP instance for each VLAN
C. one STP instance per set of VLANs
D. one STP instance per set of bridges
Answer: C

NO.9 Loop guard and UniDirectional Link Detection both protect against Layer 2 STP loops. In which two
ways does loop guard differ from UDLD in loop detection and prevention? (Choose two)
A. Loop guard can be used with root guard simultaneously on the same port on the same VLAN while
UDLD cannot.
B. UDLD protects against STP failures caused by cabling problems that create one-way links.
C. Loop guard detects and protects against duplicate packets being received and transmitted on different
ports.
D. UDLD protects against unidirectional cabling problems on copper and fiber media.
E. Loop guard protects against STP failures caused by problems that result in the loss of BPDUs from a
designated switch port
Answer: BE

NO.10 Which three port states are used by RSTP 802.1w? (Choose three.)
A. Listening
B. Learning
C. Forwarding
D. Blocking
E. Discarding
F. Disabled
Answer: BCE

NO.11 The classic Spanning Tree Protocol (802.1D 1998) uses which sequence of variables to determine the
best received BPDU?
A. 1) lowest root bridge id,
2) lowest sender bridge id,
3) lowest port id,
4) lowest root path cost
B. 1) lowest root path cost,
2) lowest root bridge id,
3) lowest sender bridge id,
4) lowest sender port id
C. 1) lowest root bridge id,
2) lowest sender bridge id,
3) lowest root path cost
4) lowest sender port id
D. 1) lowest root bridge id,
2) lowest root path cost,
3) lowest sender bridge id,
4) lowest sender port id
Answer: D

NO.12 If a port configured with STP loop guard stops receiving BPDUs, the port will be put into which state?
A. learning state
B. listening state
C. forwarding state
D. loop-inconsistent state
Answer: D

NO.13 What is the purpose of the STP PortFast BPDU guard feature?
A. enforce the placement of the root bridge in the network
B. ensure that a port is transitioned to a forwarding state quickly if a BPDU is received
C. enforce the borders of an STP domain
D. ensure that any BPDUs received are forwarded into the STP domain
Answer: C

NO.14 Refer to the exhibit.
In the diagram, the switches are running IEEE 802.1s MST. Which ports are in the MST blocking state?
A. GE-1/2 and GE-2/1
B. GE-1/1 and GE-2/2
C. GE-3/2 and GE-4/1
D. no ports are in the blocking state
E. There is not enough information to determine which ports are in the blocking state.
Answer: D

NO.15 As a network administrator, can you tell me what the root guard feature provides in a bridged network?
A. It ensures that BPDUs sent by the root bridge are forwarded in a timely manner
B. It enforces the root bridge placement in the network
C. It ensures that all ports receiving BPDUs from the root bridge are in the forwarding state.
D. It ensures that the bridge is elected as Root Bridge in the network.
Answer: B

NO.16 When STP UplinkFast is enabled on a switch utilizing the default bridge priority, what will the new bridge
priority be changed to?
A. 8192
B. 16384
C. 49152
D. 65535
Answer: C

NO.17 Which of these correctly identifies a difference between the way BPDUs are handled by 802.1w and
802.1D?
A. 802.1D bridges do not relay BPDUs.
B. 802.1w bridges do not relay BPDUs.
C. 802.1D bridges only relay BPDUs received from the root.
D. 802.1w bridges only relay BPDUs received from the root.
Answer: C

NO.18 Why does RSTP have a better convergence time than 802.1D?
A. It is newer
B. It has smaller timers
C. It has less overhead
D. It is not timer-based
Answer: D

NO.19 You have done a partial migration from 802.1D STP to 802.1w STP. Which of the following is true?
A. 802.1D and 802.1w interoperate only when the 802.1D STP domain supports rapid convergence.
B. Ports leading to 802.1D devices will run in compatibility mode, while the rest of the ports will run in
802.1w mode.
C. This is an invalid configuration and a partial migration cannot be done.
D. The bridge timers will be set to match the 802.1D devices.
E. A secondary root bridge will always be populated within the 802.1D domain.
F. If the root bridge is selected within the 802.1D domain, the whole STP domain will run in 802.1D
compatibility mode.
G. In partially migrated 802.1w networks, it is recommended to keep the STP diameter below 4.
Answer: B

NO.20 Spanning Tree Protocol calculates path cost based on which of these?
A. interface bandwidth
B. interface delay
C. interface bandwidth and delay
D. hop count
E. bridge priority
Answer: A
 
Posted 2013/4/19 2:59:18  |  Category: 미분류  |  Tag: