Pass4Test 는 완전히 여러분이 인증시험 준비와 안전한 시험패스를 위한 완벽한 덤프제공 사이트입니다.우리 Pass4Test의 덤프들은 응시자에 따라 ,시험 ,시험방법에 따라  알 맞춤한 퍼펙트한 자료입니다.여러분은 Pass4Test의 알맞춤 덤프들로 아주 간단하고 편하게  인증시험을 패스할 수 있습니다.많은  it인증관연 응시자들은  우리 Pass4Test가 제공하는 문제와 답으로 되어있는 덤프로 자격증을 취득하셨습니다.우리 Pass4Test 또한 업계에서 아주 좋은 이미지를 가지고있습니다.Pass4Test의 연구팀에서는  CCIE 351-001 (CCIE Cisco Certified InterNetworking Expe rt) 인증덤프를 위하여 최선을 다하였습니다. Pass4Test 학습가이드  CCIE 351-001 (CCIE Cisco Certified InterNetworking Expert) 덤프로 시험준비 하시면 시험이 쉬워집니다. Pass4Test에서 제공하는 문제와 답을 공부하시면 100% 시험에서 한방에 통과할것입니다.여러분이  CCIE 351-001 (CCIE Cisco Certified InterNetworking Expert) 시험에 응시하는데  Pass4Test의 도움을 받는다면 Pass4Test에서는 꼭 완벽한 자료를 드릴것을 약속합니다. 또한 일년무료 업데이트 서비스를제공합니다.즉 문제와 답이 갱신이 되었을 경우 우리는 여러분들한테 최신버전의 문제와 답을다시 보내드립니다.

 

 

NO.1 As a network administrator, can you tell me what the root guard feature provides in a bridged network?
A. It ensures that BPDUs sent by the root bridge are forwarded in a timely manner
B. It enforces the root bridge placement in the network
C. It ensures that all ports receiving BPDUs from the root bridge are in the forwarding state.
D. It ensures that the bridge is elected as Root Bridge in the network.
Answer: B

NO.2 The classic Spanning Tree Protocol (802.1D 1998) uses which sequence of variables to determine the
best received BPDU?
A. 1) lowest root bridge id,
2) lowest sender bridge id,
3) lowest port id,
4) lowest root path cost
B. 1) lowest root path cost,
2) lowest root bridge id,
3) lowest sender bridge id,
4) lowest sender port id
C. 1) lowest root bridge id,
2) lowest sender bridge id,
3) lowest root path cost
4) lowest sender port id
D. 1) lowest root bridge id,
2) lowest root path cost,
3) lowest sender bridge id,
4) lowest sender port id
Answer: D

NO.3 What is the purpose of the STP PortFast BPDU guard feature?
A. enforce the placement of the root bridge in the network
B. ensure that a port is transitioned to a forwarding state quickly if a BPDU is received
C. enforce the borders of an STP domain
D. ensure that any BPDUs received are forwarded into the STP domain
Answer: C

NO.4 When STP UplinkFast is enabled on a switch utilizing the default bridge priority, what will the new bridge
priority be changed to?
A. 8192
B. 16384
C. 49152
D. 65535
Answer: C

NO.5 Which two of these are used in the selection of a root bridge in a network utilizing Spanning Tree
Protocol IEEE 802.1D.? (Choose two)
A. Designated Root Cost
B. bridge ID priority
C. max age
D. bridge ID MAC address
E. Designated Root Priority
F. forward delay
Answer: BD

NO.6 Which standard supports multiple instances of spanning tree?
A. 802.1D
B. 802.1s
C. 802.1w
D. 802.1z
Answer: B

NO.7 Loop guard and UniDirectional Link Detection both protect against Layer 2 STP loops. In which two
ways does loop guard differ from UDLD in loop detection and prevention? (Choose two)
A. Loop guard can be used with root guard simultaneously on the same port on the same VLAN while
UDLD cannot.
B. UDLD protects against STP failures caused by cabling problems that create one-way links.
C. Loop guard detects and protects against duplicate packets being received and transmitted on different
ports.
D. UDLD protects against unidirectional cabling problems on copper and fiber media.
E. Loop guard protects against STP failures caused by problems that result in the loss of BPDUs from a
designated switch port
Answer: BE

NO.8 Prior to 802.1w, Cisco implemented a number of proprietary enhancements to 802.1D to improve
convergence in a Layer 2 network. Which statement is correct?
A. Only UplinkFast and BackboneFast are specified in 802.1w; PortFast must be manually configured.
B. Only PortFast is specified in 802.1w; UplinkFast and BackboneFast must be manually configured.
C. None of the proprietary Cisco enhancements are specified in 802.1w.
D. PortFast, UplinkFast, and BackboneFast are specified in 802.1w.
Answer: D

NO.9 You have done a partial migration from 802.1D STP to 802.1w STP. Which of the following is true?
A. 802.1D and 802.1w interoperate only when the 802.1D STP domain supports rapid convergence.
B. Ports leading to 802.1D devices will run in compatibility mode, while the rest of the ports will run in
802.1w mode.
C. This is an invalid configuration and a partial migration cannot be done.
D. The bridge timers will be set to match the 802.1D devices.
E. A secondary root bridge will always be populated within the 802.1D domain.
F. If the root bridge is selected within the 802.1D domain, the whole STP domain will run in 802.1D
compatibility mode.
G. In partially migrated 802.1w networks, it is recommended to keep the STP diameter below 4.
Answer: B

NO.10 Refer to the exhibit.
In the diagram, the switches are running IEEE 802.1s MST. Which ports are in the MST blocking state?
A. GE-1/2 and GE-2/1
B. GE-1/1 and GE-2/2
C. GE-3/2 and GE-4/1
D. no ports are in the blocking state
E. There is not enough information to determine which ports are in the blocking state.
Answer: D

NO.11 Why does RSTP have a better convergence time than 802.1D?
A. It is newer
B. It has smaller timers
C. It has less overhead
D. It is not timer-based
Answer: D

NO.12 What two features in Cisco switches help prevent Layer 2 loops? (Choose two)
A. UniDirectional Link Detection
B. Hot Standby Router Protocol
C. Virtual Router Redundancy Protocol
D. PortFast
E. Root guard
F. Loop guard
Answer: AF

NO.13 Refer to the exhibit.
In the diagram, the switches are running IEEE 802.1w RSPT.
On which ports should root guard be enabled in order to facilitate deterministic root bridge election under
normal and failure scenarios?
A. GE-3/1, GE-3/2
B. FE-2/1, FE-3/2
C. GE-1/1.GE-1/2
D. GE-4/1, GE-4/2
E. GE-2/1, GE-2/2
F. GE-3/1, GE-3/2, GE-4/1, GE-4/2, FE-2/1, FE-3/2
Answer: F

NO.14 Which of these correctly identifies a difference between the way BPDUs are handled by 802.1w and
802.1D?
A. 802.1D bridges do not relay BPDUs.
B. 802.1w bridges do not relay BPDUs.
C. 802.1D bridges only relay BPDUs received from the root.
D. 802.1w bridges only relay BPDUs received from the root.
Answer: C

NO.15 Under which two circumstances would an RSTP bridge flush its CAM table? (Choose two)
A. Upon a port state change
B. Upon receiving a topology change notification
C. When transitioning from discarding to forwarding
D. When transitioning from forwarding to discarding
E. Only when changing from listening to discarding
F. When CAM resources have been completely used up
Answer: BC

NO.16 Spanning Tree Protocol calculates path cost based on which of these?
A. interface bandwidth
B. interface delay
C. interface bandwidth and delay
D. hop count
E. bridge priority
Answer: A

NO.17 Refer to the exhibit.
Which switching feature is being tested?
A. loop guard
B. PortFast
C. root guard
D. BDPU guard
Answer: A

NO.18 Spanning Tree Protocol IEEE 802.1s defines the ability to deploy which of these?
A. one global STP instance for all VLANs
B. one STP instance for each VLAN
C. one STP instance per set of VLANs
D. one STP instance per set of bridges
Answer: C

NO.19 Which three port states are used by RSTP 802.1w? (Choose three.)
A. Listening
B. Learning
C. Forwarding
D. Blocking
E. Discarding
F. Disabled
Answer: BCE

NO.20 If a port configured with STP loop guard stops receiving BPDUs, the port will be put into which state?
A. learning state
B. listening state
C. forwarding state
D. loop-inconsistent state
Answer: D