IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2) 인증시험은 난이도가 높아 패스하기 어렵습니다.IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2) 시험은 IT업계에서도 권위가 있고 직위가 있으신 분들이 응시할 수 있는 시험이라고 알려져 있습니다. 우리 Pass4Test에서는  IBM 000-332 (High Availability for AIX - Technical Support and Administr ation -v2) 관련 학습가이드를 제공합니다. Pass4Test 는 우리만의 IT전문가들이 만들어낸 IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2) 관련 최신, 최고의 자료와 학습가이드를 준비하고 있습니다.  여러분의  IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2) 시험에 응시하는데 많은 도움이 될 것입니다.Pass4Test를 선택하였다면 여러분은 반은 성공한 것입니다. 여러분은 아주 빠르게 안전하게 또 쉽게 IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2) 인증시험 자격증을 취득하실 수 있습니다. 우리 Pass4Test에서 제공되는 모든 덤프들은 모두 100%합격율을 자랑하며 제일 퍼펙트한 서비스를 제공해드립니다.여러분은 IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2) 인증시험을 패스함으로 IT업계관련 직종에 종사하려는 분들에게는 아주 큰 가산점이 될수 있으며, 성공한 IT업계전문가와 한걸음 가까워 집니다.

 

 

NO.1 Consider the following PowerHA DLPAR configuration for a cluster, and LPAR profile on the HMC for a
standby node in that cluster: How should the standby node profile be reconfigured so that an application
runs with the minimum hardware resources?
A. Minimum and Desired processing units = 0.1 and Maximum processing units = 0.6
B. Minimum and Desired processing units = 0.2 and Maximum processing units = 0.5
C. Minimum processing units = 0.6 and both Desired and Maximum processing units = 1.5
D. Minimum processing units = 0.5 and both Desired and Maximum processing units = 0.9
Answer: D

NO.2 An administrator is planning to upgrade from HACMP 5.5 and AIX 5.3 to PowerHA 7 and AIX 7. After
migration installing AIX, what must be done first?
A. Install CAAfileset.
B. Migrate to PowerHA 7.
C. Run the clmigcheck program.
D. Create shared VG for use by CAA.
Answer: C

NO.3 There is a two-node cluster with Node1 and Node2. An administrator changes filesystem size on Node1
by using the chfs command, and moves resource the group to Node2.
The administrator finds the change of filesystem size is recognized on Node2.
Why is the filesystem size change reflected on Node2?
A. The gsclvmd daemon automatically synchronizes filesystem changes.
B. The filesystem size change is recognized when filesystem is mounted on Node2.
C. A pre-event is defined to get_disk_vg_fs event to reflect filesystem size change.
D. The shared volume group is re-imported on Node2 by lazy update when moving the resource group.
Answer: A

NO.4 What cluster service settings can be defined in SMIT on one node of a cluster and automatically
updated on all other nodes?
A. BROADCAST message at startup
B. Start HACMP at system restart
C. Verify Cluster Prior to Startup
D. Startup Cluster Information Daemon
Answer: A

NO.5 The service IPs VLAN is the only routable network in a 2-node HA cluster with multiple network
interfaces. What must done to enable administrative tasks to be performed remotely on the cluster
nodes?
A. Associate a permanent Service IP address for each HA node.
B. Configure the boot IP Address on the same VLAN as the service IP Address.
C. Configure a persistent IP Address for each node on the service IP network.
D. Create a route on the switch and translate the Service IP address to the boot IP address using NAT.
Answer: C

NO.6 When implementing PowerHA in a cross site LVM configuration, which logical volume option is
required.?
A. Serialize IO=yes
B. Mirror Write Consistency=on
C. Scheduling Policy=sequential
D. Allocation Policy=superstrict
Answer: D

NO.7 An administrator is using PowerHA 7 to define a new cluster using SMIT option "Setup a Cluster, Nodes
and Networks" and encountered the following error message:
What is the root cause of the problem?
A. The nodes were not defined in the DNS
B. The /etc/cluster/rhosts are not populated correctly
C. The CAA repository disk is not accessible on all nodes
D. The CAA cluster was not defined before defining the PowerHA Cluster
Answer: B

NO.8 When PowerHA SystemMirror 7.1 is installed on AIX 7.1, what RSCT component does Cluster Aware
AIX (CAA) replace?
A. Group Services
B. Resource Manager
C. Topology Services
D. Resource Monitoring and Control (RMC)
Answer: A

NO.9 Given the information from hacmp.out below, why is the cluster in config_too_long status?
A. The script /APP1/serv/scripts/shut_down does not exist.
B. The APP1 stop_server script exited with a non zero return code.
C. The application did not shut down correctly, which caused the rg_move operation to exceed the time
limit to complete.
D. The rg_move event is sleeping for anything between 360 seconds and 3600 hours until the
stop_server script is complete.
Answer: B

NO.10 A 2-node cluster has three multi-node disk heartbeat (MNDHB) networks and data volume groups on
separate disks. Application resource groups are online on Node1. What happens if Node1 loses access to
two of the three MNDHB disks?
A. Node1 halts
B. Application resource groups move to Node2
C. Application resource groups remain on Node1
D. Application resource groups on Node1 go offline
Answer: B