현재 IBM  CATE 000-332 인증시험을 위하여 노력하고 계십니까? 최대한 빠르게 IBM  CATE 000-332 시험자격증을 취득하고 싶으시다면 우리 Pass4Test 의 덤프를 선택하시면 됩니다. Pass4Test를 선택함으로 IBM  CATE 000-332  인증시험패스는 꿈이 아닌 현실로 다가올 것입니다.  우리  Pass4Test의 IBM  CATE 000-332 덤프는 여러분이 IBM  CATE 000-332 인증시험 응시에 도움이 되도록제공되는 것입니다.Pass4Test에서 제공되는 학습가이드에는 IBM  CATE 000-332 인증시험 관연 정보기술로 여러분이 이 분야의 지식 장악에 많은 도움이 될 것이며 또한 아주 정확한 IBM  CATE 000-332 시험문제와 답으로 여러분은 한번에 안전하게 시험을 패스하실 수 있습니다.IBM  CATE 000-332  인증시험을 아주 높은 점수로 패스할 것을 보장해 드립니다.많은 사이트에서도 무료 IBM  CATE 000-332 덤프데모를 제공합니다.우리도 마찬가지입니다.여러분은 IBM  CATE 000-332  데모들을 보시고 다시 우리의 덤프와 비교하시면 우리의 덤프는 다른 사이트덤프와 차원이 다른 덤프임을 아시게 될것입니다. 우리 Pass4Test에서 제공되는 덤프는 100%보장도를 자랑하며 여러분은 시험패스로 인해 성공과 더 가까워질것입니다.

 

 

 

NO.1 What cluster service settings can be defined in SMIT on one node of a cluster and automatically
updated on all other nodes?
A. BROADCAST message at startup
B. Start HACMP at system restart
C. Verify Cluster Prior to Startup
D. Startup Cluster Information Daemon
Answer: A

NO.2 An administrator is planning to upgrade from HACMP 5.5 and AIX 5.3 to PowerHA 7 and AIX 7. After
migration installing AIX, what must be done first?
A. Install CAAfileset.
B. Migrate to PowerHA 7.
C. Run the clmigcheck program.
D. Create shared VG for use by CAA.
Answer: C

NO.3 A 2-node cluster has three multi-node disk heartbeat (MNDHB) networks and data volume groups on
separate disks. Application resource groups are online on Node1. What happens if Node1 loses access to
two of the three MNDHB disks?
A. Node1 halts
B. Application resource groups move to Node2
C. Application resource groups remain on Node1
D. Application resource groups on Node1 go offline
Answer: B

NO.4 When implementing PowerHA in a cross site LVM configuration, which logical volume option is
required.?
A. Serialize IO=yes
B. Mirror Write Consistency=on
C. Scheduling Policy=sequential
D. Allocation Policy=superstrict
Answer: D

NO.5 There is a two-node cluster with Node1 and Node2. An administrator changes filesystem size on Node1
by using the chfs command, and moves resource the group to Node2.
The administrator finds the change of filesystem size is recognized on Node2.
Why is the filesystem size change reflected on Node2?
A. The gsclvmd daemon automatically synchronizes filesystem changes.
B. The filesystem size change is recognized when filesystem is mounted on Node2.
C. A pre-event is defined to get_disk_vg_fs event to reflect filesystem size change.
D. The shared volume group is re-imported on Node2 by lazy update when moving the resource group.
Answer: A

NO.6 An administrator is using PowerHA 7 to define a new cluster using SMIT option "Setup a Cluster, Nodes
and Networks" and encountered the following error message:
What is the root cause of the problem?
A. The nodes were not defined in the DNS
B. The /etc/cluster/rhosts are not populated correctly
C. The CAA repository disk is not accessible on all nodes
D. The CAA cluster was not defined before defining the PowerHA Cluster
Answer: B

NO.7 The service IPs VLAN is the only routable network in a 2-node HA cluster with multiple network
interfaces. What must done to enable administrative tasks to be performed remotely on the cluster
nodes?
A. Associate a permanent Service IP address for each HA node.
B. Configure the boot IP Address on the same VLAN as the service IP Address.
C. Configure a persistent IP Address for each node on the service IP network.
D. Create a route on the switch and translate the Service IP address to the boot IP address using NAT.
Answer: C

NO.8 When PowerHA SystemMirror 7.1 is installed on AIX 7.1, what RSCT component does Cluster Aware
AIX (CAA) replace?
A. Group Services
B. Resource Manager
C. Topology Services
D. Resource Monitoring and Control (RMC)
Answer: A

NO.9 Given the information from hacmp.out below, why is the cluster in config_too_long status?
A. The script /APP1/serv/scripts/shut_down does not exist.
B. The APP1 stop_server script exited with a non zero return code.
C. The application did not shut down correctly, which caused the rg_move operation to exceed the time
limit to complete.
D. The rg_move event is sleeping for anything between 360 seconds and 3600 hours until the
stop_server script is complete.
Answer: B

NO.10 Consider the following PowerHA DLPAR configuration for a cluster, and LPAR profile on the HMC for a
standby node in that cluster: How should the standby node profile be reconfigured so that an application
runs with the minimum hardware resources?
A. Minimum and Desired processing units = 0.1 and Maximum processing units = 0.6
B. Minimum and Desired processing units = 0.2 and Maximum processing units = 0.5
C. Minimum processing units = 0.6 and both Desired and Maximum processing units = 1.5
D. Minimum processing units = 0.5 and both Desired and Maximum processing units = 0.9
Answer: D