IBM CATE 000-332 인증시험은 F5인증시험중의 하나입니다.그리고 또한 비중이 아주 큰 인증시험입니다. IBM CATE 000-332  인증시험 패스는 정말 어렵다고 생각됩니다. 우리 Pass4Test에서는 여러분이   IBM CATE 000-332 인증시험을 부담없이 응시할수 있도록 전문적인 연구팀에서 만들어낸 최고의   IBM CATE 000-332 덤프를 제공해드립니다.Pass4Test와 만남으로 여러분은 아주 간편하게 어려운 시험을 패스하실 수 있습니다. Pass4Test에는 베터랑의 전문가들로 이루어진 연구팀이 있습니다. 그들은 풍부한  IT지식과  경험으로  여러분이 IBM CATE 000-332 시험을 패스할 수 있도록  학습가이드를 만들었습니다, Pass4Test 에서는 일년무료 업데이트를 제공해드리며 Pass4Test 의 덤프들은 모두 높은 적중율을 자랑합니다. Pass4Test를  선택함으로 여러분이  IBM CATE 000-332 시험에 대한 부담은 사라질 것입니다.우리 Pass4Test는 끊임없는 업데이트로 항상 최신버전의   IBM CATE 000-332 시험덤프를 제공하는 사이트입니다.만약 덤프품질을 확인하고 싶다면 우리 Pass4Test 에서 무료로 제공되는 덤프의 일부분 문제를 체험하시면 됩니다.Pass4Test 는 100%의 보장도를 자랑하며 IBM CATE 000-332 시험을 한번에 패스하도록 도와드립니다.

 

 

NO.1 What cluster service settings can be defined in SMIT on one node of a cluster and automatically
updated on all other nodes?
A. BROADCAST message at startup
B. Start HACMP at system restart
C. Verify Cluster Prior to Startup
D. Startup Cluster Information Daemon
Answer: A

NO.2 There is a two-node cluster with Node1 and Node2. An administrator changes filesystem size on Node1
by using the chfs command, and moves resource the group to Node2.
The administrator finds the change of filesystem size is recognized on Node2.
Why is the filesystem size change reflected on Node2?
A. The gsclvmd daemon automatically synchronizes filesystem changes.
B. The filesystem size change is recognized when filesystem is mounted on Node2.
C. A pre-event is defined to get_disk_vg_fs event to reflect filesystem size change.
D. The shared volume group is re-imported on Node2 by lazy update when moving the resource group.
Answer: A

NO.3 When PowerHA SystemMirror 7.1 is installed on AIX 7.1, what RSCT component does Cluster Aware
AIX (CAA) replace?
A. Group Services
B. Resource Manager
C. Topology Services
D. Resource Monitoring and Control (RMC)
Answer: A

NO.4 An administrator is using PowerHA 7 to define a new cluster using SMIT option "Setup a Cluster, Nodes
and Networks" and encountered the following error message:
What is the root cause of the problem?
A. The nodes were not defined in the DNS
B. The /etc/cluster/rhosts are not populated correctly
C. The CAA repository disk is not accessible on all nodes
D. The CAA cluster was not defined before defining the PowerHA Cluster
Answer: B

NO.5 Given the information from hacmp.out below, why is the cluster in config_too_long status?
A. The script /APP1/serv/scripts/shut_down does not exist.
B. The APP1 stop_server script exited with a non zero return code.
C. The application did not shut down correctly, which caused the rg_move operation to exceed the time
limit to complete.
D. The rg_move event is sleeping for anything between 360 seconds and 3600 hours until the
stop_server script is complete.
Answer: B

NO.6 The service IPs VLAN is the only routable network in a 2-node HA cluster with multiple network
interfaces. What must done to enable administrative tasks to be performed remotely on the cluster
nodes?
A. Associate a permanent Service IP address for each HA node.
B. Configure the boot IP Address on the same VLAN as the service IP Address.
C. Configure a persistent IP Address for each node on the service IP network.
D. Create a route on the switch and translate the Service IP address to the boot IP address using NAT.
Answer: C

NO.7 An administrator is planning to upgrade from HACMP 5.5 and AIX 5.3 to PowerHA 7 and AIX 7. After
migration installing AIX, what must be done first?
A. Install CAAfileset.
B. Migrate to PowerHA 7.
C. Run the clmigcheck program.
D. Create shared VG for use by CAA.
Answer: C

NO.8 A 2-node cluster has three multi-node disk heartbeat (MNDHB) networks and data volume groups on
separate disks. Application resource groups are online on Node1. What happens if Node1 loses access to
two of the three MNDHB disks?
A. Node1 halts
B. Application resource groups move to Node2
C. Application resource groups remain on Node1
D. Application resource groups on Node1 go offline
Answer: B

NO.9 When implementing PowerHA in a cross site LVM configuration, which logical volume option is
required.?
A. Serialize IO=yes
B. Mirror Write Consistency=on
C. Scheduling Policy=sequential
D. Allocation Policy=superstrict
Answer: D

NO.10 Consider the following PowerHA DLPAR configuration for a cluster, and LPAR profile on the HMC for a
standby node in that cluster: How should the standby node profile be reconfigured so that an application
runs with the minimum hardware resources?
A. Minimum and Desired processing units = 0.1 and Maximum processing units = 0.6
B. Minimum and Desired processing units = 0.2 and Maximum processing units = 0.5
C. Minimum processing units = 0.6 and both Desired and Maximum processing units = 1.5
D. Minimum processing units = 0.5 and both Desired and Maximum processing units = 0.9
Answer: D