현재  Cisco Specialist 648-375 인증시험을 위하여 노력하고 계십니까? 최대한 빠르게  Cisco Specialist 648-375 시험자격증을 취득하고 싶으시다면 우리 Pass4Test 의 덤프를 선택하시면 됩니다. Pass4Test를 선택함으로  Cisco Specialist 648-375 인증시험패스는 꿈이 아닌 현실로 다가올 것입니다.  우리  Pass4Test의  Cisco Specialist 648-375  덤프는 여러분이  Cisco Specialist 648-375 인증시험 응시에 도움이 되도록 제공되는 것입니다.Pass4Test에서 제공되는 학습가이드에는  Cisco Specialist 648-375  인증시험 관연 정보기술로 여러분이 이 분야의 지식 장악에 많은 도움이 될 것이며 또한 아주 정확한  Cisco Specialist 648-375 시험문제와 답으로 여러분은 한번에 안전하게 시험을 패스하실 수 있습니다. Cisco Specialist 648-375  인증시험을 아주 높은 점수로 패스할 것을 보장해 드립니다.많은 사이트에서도 무료  Cisco Specialist 648-375 덤프데모를 제공합니다.우리도 마찬가지입니다.여러분은  Cisco Specialist 648-375 데모들을 보시고 다시 우리의 덤프와 비교하시면 우리의 덤프는 다른 사이트덤프와 차원이 다른 덤프임을 아시게 될것입니다. 우리 Pass4Test에서 제공되는 덤프는 100%보장도를 자랑하며 여러분은 시험패스로 인해 성공과 더 가까워질것입니다.

 

 

NO.1 You are working with a company that has an infrastructure based on lightweight access points
using the advanced feature set. A new security requirement demands real-time asset tracking for
800 assets. Which product or solution will provide this function?
A. Wireless Control System
B. Wireless Location Appliance
C. Wireless LAN Solution Engine
D. Wireless LAN Services Module
Answer: B

NO.2 Which VMS Security Monitor tool allows you to monitor data for patterns of attacks from one
machine to a list of targets?
A. Advanced Correlation Engine
B. Management Center for CSA
C. CiscoWorks Dashboard
D. Advanced Notification Engine
Answer: A

NO.3 What are two of the four key benefits of the ISR platforms? (Choose two)
A. monitoring, analysis, and response
B. investment protection
C. guest access
D. voice and mobility ready
E. storage virtualization
Answer: B,D

NO.4 What is the purpose of the Dynamic Configuration Tool?
A. to allow for the mass deployment of devices with minimal configurations
B. to provide an easy way to check for known bugs in IOS releases
C. to determine the correct IOS image to support your modules or blades
D. to test router configurations virtually prior to implementing them in your production network
E. to verify that hardware such as modules are compatible with your chassis
Answer: E

NO.5 What should you keep in mind when working with antennas?
A. Antennas can be used as transmit and receive antennas on the same radio
B. All antennas broadcast the horizontal plane
C. Isotropic antennas broadcast equally in all directions
D. An antennas that converts electrical energy into RF waves is called a receive antenna
Answer: C

NO.6 What should you do to prevent VLAN hopping?
A. Enable all unused ports and place them into an unused VLAN
B. Set unused access ports to trunking ON
C. Disable some unused ports
D. Disable all unused ports and place them into an unused VLAN
Answer: D

NO.7 Which of these is a benefit of an integrated security management system?
A. It provides configuration, monitoring, and troubleshooting capabilities across a wide range of
security products.
B. It leverages existing network management systems such as HP OpenView to lower the cost of
implementation.
C. It integrates security management capabilities into the router or switch.
D. It integrates security device management products and collects events on an "as needed" basis
to reduce management overhead.
E. It provides a single point of contact for all security configuration tasks thereby enhancing the
return on investment.
Answer: A

NO.8 What should you keep in mind when using a midspan PSE?
A. It can be used to deliver PoE over 100BASE-T connections
B. It can implement power delivery only over the spare wires of the copper cabling
C. It defines terminology to describe a port that acts as a PSE to a powered device
D. It states that power can be delivered by an end-point PSE
Answer: B

NO.9 Which of these is an accurate list of Cisco Lifecycle Services phases?
A. project planning, site assessment, risk assessment, solution selection and acquisition, testing,
and operations
B. analysis, design, deployment, testing, implementation, and production
C. prepare, plan, design, implement, operate, and optimize
D. initiation, planning, analysis, design, development, implementation, operations and
maintenance
E. presales, project planning, development, implementation, operations testing, and operations
sign-off
Answer: C

NO.10 In the plan phase, network readiness assessment addresses the optimal technologies for
supporting its business requirements and objectives
A. TRUE
B. FALSE
Answer: B