만약 아직도  Cisco Specialist 648-375 시험패스를 위하여 고군분투하고 있다면 바로 우리 Pass4Test를 선택함으로 여러분의 고민을 날려버릴수 있습니다. 우리 Pass4Test에서는 최고의 최신의 덤프자료를 제공 함으로 여러분을 도와  Cisco Specialist 648-375 인증자격증을 쉽게 취득할 수 있게 해드립니다. 만약  Cisco Specialist 648-375 인증시험으로 한층 업그레이드된 자신을 만나고 싶다면 우리 Pass4Test선택을 후회하지 않을 것입니다. 우리 Pass4Test과의 만남으로 여러분은 한번에 아주 간편하게  Cisco Specialist 648-375 시험을 패스하실 수 있으며  Cisco Specialist 648-375 자격증으로 완벽한 스펙을 쌓으실 수 있습니다. Pass4 Test에서 제공하는 제품들은 품질이 아주 좋으며 또 업뎃속도도 아주 빠릅니다 . 우리가 제공하는  Cisco Specialist 648-375 인증시험관련 덤프를 구매하신다면  Cisco Specialist 648-375 시험은 손쉽게 성공적으로 패스하실 수 있습니다.Pass4Test는 여러분의꿈을 이루어줄 뿐만 아니라 일년무료 업뎃서비스도 제공해드립니다. Pass4Test에서 제공하는 덤프로 여러분은 100%시험을 패스하실수 있고  Cisco Specialist 648-375 자격증을 취득하실 수 있습니다.지금 바로 사이트에서  Cisco Specialist 648-375 덤프데모즉 덤프의 일부 문제와 답을 다운 받으셔서 체험하실 수 있습니다.

 

 

NO.1 You are working with a company that has an infrastructure based on lightweight access points
using the advanced feature set. A new security requirement demands real-time asset tracking for
800 assets. Which product or solution will provide this function?
A. Wireless Control System
B. Wireless Location Appliance
C. Wireless LAN Solution Engine
D. Wireless LAN Services Module
Answer: B

NO.2 What should you keep in mind when using a midspan PSE?
A. It can be used to deliver PoE over 100BASE-T connections
B. It can implement power delivery only over the spare wires of the copper cabling
C. It defines terminology to describe a port that acts as a PSE to a powered device
D. It states that power can be delivered by an end-point PSE
Answer: B

NO.3 What is the purpose of the Dynamic Configuration Tool?
A. to allow for the mass deployment of devices with minimal configurations
B. to provide an easy way to check for known bugs in IOS releases
C. to determine the correct IOS image to support your modules or blades
D. to test router configurations virtually prior to implementing them in your production network
E. to verify that hardware such as modules are compatible with your chassis
Answer: E

NO.4 Which VMS Security Monitor tool allows you to monitor data for patterns of attacks from one
machine to a list of targets?
A. Advanced Correlation Engine
B. Management Center for CSA
C. CiscoWorks Dashboard
D. Advanced Notification Engine
Answer: A

NO.5 Which of these is a benefit of an integrated security management system?
A. It provides configuration, monitoring, and troubleshooting capabilities across a wide range of
security products.
B. It leverages existing network management systems such as HP OpenView to lower the cost of
implementation.
C. It integrates security management capabilities into the router or switch.
D. It integrates security device management products and collects events on an "as needed" basis
to reduce management overhead.
E. It provides a single point of contact for all security configuration tasks thereby enhancing the
return on investment.
Answer: A

NO.6 What should you do to prevent VLAN hopping?
A. Enable all unused ports and place them into an unused VLAN
B. Set unused access ports to trunking ON
C. Disable some unused ports
D. Disable all unused ports and place them into an unused VLAN
Answer: D

NO.7 In the plan phase, network readiness assessment addresses the optimal technologies for
supporting its business requirements and objectives
A. TRUE
B. FALSE
Answer: B

NO.8 What are two of the four key benefits of the ISR platforms? (Choose two)
A. monitoring, analysis, and response
B. investment protection
C. guest access
D. voice and mobility ready
E. storage virtualization
Answer: B,D

NO.9 What should you keep in mind when working with antennas?
A. Antennas can be used as transmit and receive antennas on the same radio
B. All antennas broadcast the horizontal plane
C. Isotropic antennas broadcast equally in all directions
D. An antennas that converts electrical energy into RF waves is called a receive antenna
Answer: C

NO.10 Which of these is an accurate list of Cisco Lifecycle Services phases?
A. project planning, site assessment, risk assessment, solution selection and acquisition, testing,
and operations
B. analysis, design, deployment, testing, implementation, and production
C. prepare, plan, design, implement, operate, and optimize
D. initiation, planning, analysis, design, development, implementation, operations and
maintenance
E. presales, project planning, development, implementation, operations testing, and operations
sign-off
Answer: C