Pass4Test에는 전문적인 업계인사들이  IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2)   시험문제와 답에 대하여 연구하여  시험준비중인 여러분들한테 유용하고 필요한 시험가이드를 제공합니다. 만약 Pass4Test의 제품을 구매하려면 우리Pass4Test에서는 아주 디테일 한 설명과 최신버전 최고품질의 자료를 적중율이 높은 문제와 답을 제공합니다.아직도 어떻게 하면  IBM 000-332 (High Availability for AIX - Technical Support and Administra tion -v2)   인증시험을 빠르게 취득할 수 있는 방법을 못찾고 계십니까?  Pass4Test의 자료는 차원이 다른 완벽한 자료입니다.100%통과율은 물론 Pass4Test을 선택으로 여러분의 직장생활에 더 낳은 개변을 가져다 드립니다.지금 Pass4Test에서   IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2)  인증시험을 안전하게 넘을 수 있도록 대책을 내드리겠습니다. 아주 신기한 효과가 있을 것입니다. IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2)  자료는 충분한 시험대비 자료가 될 것입니다. 안심하시고 Pass4Test가 제공하는 제품을 사용하시고 100%통과 율을 확신합니다.다른 사이트에서도   IBM 000-332 (High Availability for AIX - Technical Support and Administration -v2)   인증시험 관련 자료를 보셨다고 믿습니다.

 

 

NO.1 When PowerHA SystemMirror 7.1 is installed on AIX 7.1, what RSCT component does Cluster Aware
AIX (CAA) replace?
A. Group Services
B. Resource Manager
C. Topology Services
D. Resource Monitoring and Control (RMC)
Answer: A

NO.2 An administrator is planning to upgrade from HACMP 5.5 and AIX 5.3 to PowerHA 7 and AIX 7. After
migration installing AIX, what must be done first?
A. Install CAAfileset.
B. Migrate to PowerHA 7.
C. Run the clmigcheck program.
D. Create shared VG for use by CAA.
Answer: C

NO.3 What cluster service settings can be defined in SMIT on one node of a cluster and automatically
updated on all other nodes?
A. BROADCAST message at startup
B. Start HACMP at system restart
C. Verify Cluster Prior to Startup
D. Startup Cluster Information Daemon
Answer: A

NO.4 There is a two-node cluster with Node1 and Node2. An administrator changes filesystem size on Node1
by using the chfs command, and moves resource the group to Node2.
The administrator finds the change of filesystem size is recognized on Node2.
Why is the filesystem size change reflected on Node2?
A. The gsclvmd daemon automatically synchronizes filesystem changes.
B. The filesystem size change is recognized when filesystem is mounted on Node2.
C. A pre-event is defined to get_disk_vg_fs event to reflect filesystem size change.
D. The shared volume group is re-imported on Node2 by lazy update when moving the resource group.
Answer: A

NO.5 A 2-node cluster has three multi-node disk heartbeat (MNDHB) networks and data volume groups on
separate disks. Application resource groups are online on Node1. What happens if Node1 loses access to
two of the three MNDHB disks?
A. Node1 halts
B. Application resource groups move to Node2
C. Application resource groups remain on Node1
D. Application resource groups on Node1 go offline
Answer: B

NO.6 When implementing PowerHA in a cross site LVM configuration, which logical volume option is
required.?
A. Serialize IO=yes
B. Mirror Write Consistency=on
C. Scheduling Policy=sequential
D. Allocation Policy=superstrict
Answer: D

NO.7 The service IPs VLAN is the only routable network in a 2-node HA cluster with multiple network
interfaces. What must done to enable administrative tasks to be performed remotely on the cluster
nodes?
A. Associate a permanent Service IP address for each HA node.
B. Configure the boot IP Address on the same VLAN as the service IP Address.
C. Configure a persistent IP Address for each node on the service IP network.
D. Create a route on the switch and translate the Service IP address to the boot IP address using NAT.
Answer: C

NO.8 Consider the following PowerHA DLPAR configuration for a cluster, and LPAR profile on the HMC for a
standby node in that cluster: How should the standby node profile be reconfigured so that an application
runs with the minimum hardware resources?
A. Minimum and Desired processing units = 0.1 and Maximum processing units = 0.6
B. Minimum and Desired processing units = 0.2 and Maximum processing units = 0.5
C. Minimum processing units = 0.6 and both Desired and Maximum processing units = 1.5
D. Minimum processing units = 0.5 and both Desired and Maximum processing units = 0.9
Answer: D

NO.9 An administrator is using PowerHA 7 to define a new cluster using SMIT option "Setup a Cluster, Nodes
and Networks" and encountered the following error message:
What is the root cause of the problem?
A. The nodes were not defined in the DNS
B. The /etc/cluster/rhosts are not populated correctly
C. The CAA repository disk is not accessible on all nodes
D. The CAA cluster was not defined before defining the PowerHA Cluster
Answer: B

NO.10 Given the information from hacmp.out below, why is the cluster in config_too_long status?
A. The script /APP1/serv/scripts/shut_down does not exist.
B. The APP1 stop_server script exited with a non zero return code.
C. The application did not shut down correctly, which caused the rg_move operation to exceed the time
limit to complete.
D. The rg_move event is sleeping for anything between 360 seconds and 3600 hours until the
stop_server script is complete.
Answer: B