Pass4Test의  HP HP0-Y32 (Design and Troubleshooting Open Standard Networks) 덤프는 인터넷에서 검색되는 HP HP0-Y32 (Design and Troubleshooting Open Standard Networks) 시험공부자료중 가장 출중한 시험준비 자료입니다. HP HP0-Y32 (Design and Troubleshooting Open Standard Networks) 덤프를 공부하면 시험패스는 물론이고 IT지식을 더 많이 쌓을수 있어 일거량득입니다.자격증을 취득하여 자신있게 승진하여 연봉협상하세요.

 

NO.1 Click the Exhibit button.
A user adds an untagged link between switch 20c and 30b. Which link transitions are blocked on subnet
20?
A. link from 20b to 20c
B. link from 20a to 20c
C. link from 20a to 20b
D. link from 20c to 30b
Answer: C

NO.2 Based on these basic facts, what can you "rule out" as possible causes of this problem? (Select three.)
A. the external gateway having no route to VLAN 2
B. misconfigured clients in VLAN1
C. a transient layer 1 issue
D. the firewall enabled on the client causing connectivity issues
E. a loop in VLAN1
Answer: ACD

NO.3 Click the Exhibit button.
Which issue does the Optical Time Domain Reflectometer (OTDR) show?
A. out of phase
B. extensive attenuation
C. loss of [optical] signal
D. bend or kink in the optical cable
E. low frequency roll-off C:\Pasban Work\Cert Paper
Exams\HP\HP0-Y32\HP0-Y32-A-Extracted\HP0-Y32-A-Extracted\HP0-Y32-A\23.JPG
Answer: D

NO.4 You install new category 6a home run network cables for all users. You test a random sampling of the
cables, and they all pass. Users are complaining about dropped packets, slowness, and other intermittent
results. What is the best tool to use for initial troubleshooting?
A. Simple Network Management Protocol (SNMP)
B. Time Domain Reflectometer (TDR)
C. Packet Analyzer
D. HP Intelligent Communications Manager (ICM)
Answer: B

NO.5 Which step will provide helpful information about the issue?
A. Analyze the port statistics for the client you are pinging from.
B. Compare the arp table entries on the client when it works and when it does not.
C. Analyze the port statistics for the switch to which the client is connected.
D. Analyze the port statistics for all clients in VLAN 2 when the problem occurs.
Answer: B

NO.6 Click the Exhibit button.
You need to limit the amount of broadcast traffic in this customer's network. In order to do so, you add a
second VLAN, VLAN2 (10.0.1.0/24). Now, clients on VLAN2 cannot reach the Internet and cannot ping
clients on VLAN1. They can successfully ping the default gateway (10.0.1.1). What should you do first to
determine the cause of the problem?
A. Disable broadcast limiting on the core switch.
B. Check the ISP's firewall settings and modify accordingly.
C. Request the configuration of the network devices.
D. Request a network trace from the ISP.
E. Get the MAC address table of the network devices.
Answer: C

NO.7 Click the Exhibit button.
A user adds an untagged link between switch 20c and 30b. What is the impact of the user's actions?
A. Internet connectivity to subnet 20 users is broken.
B. STP Root Bridge of Subnet 20 moves.
C. All Subnet 20 traffic is routed through Subnet 30.
D. STP alternate path selection remains unchanged.
Answer: B

NO.8 Click the Exhibit button.
You install two E5400 zl Series switches and connect them with a two-port static trunk. All hosts on both
switches are in VLAN 20. However, some hosts on Core 1 cannot ping some hosts on Core 2 and vice
versa. All hosts can ping all hosts on their own switch. Event logs on the two switches do not show
significant errors. What should you do to determine the cause of this connectivity issue? (Select three.)
A. Use traceroute to determine which device is dropping the ping packets.
B. Verify the trunk configuration on each core switch.
C. Change the IP address for the default VLAN on Core 2 so that it is in the same subnet as the default
VLAN on Core 1.
D. Verify physical connectivity between the switches.
E. Use LLDP to check the identities of the devices and their neighbors.
Answer: BDE

NO.9 You are working with a customer who has reported connectivity issues on a specific VLAN. All of their
clients were previously in VLAN1 until VLAN10 was added in order to limit the amount of broadcast traffic.
Now, the clients on VLAN10 cannot reach the Internet. These clients cannot ping clients on VLAN1, but
can successfully ping the default gateway. Which information will help you troubleshoot this problem?
(Select two.)
A. network topology map
B. uptime of the network devices
C. network IP addressing scheme
D. names of all VLANS
E. a list of the NTP servers on the network
Answer: AC

NO.10 Click the Exhibit button.
A user adds an untagged link between switch 20c and 30b. Which action can you take that will help you
discover this new link?
A. Investigate switch syslog information for gateway changes.
B. Compare route tables of both routers.
C. Review LLDP information on subnet 20 root bridge.
D. Follow path cost to root from subnet 20.
E. Initiate a traceroute from both subnets.
Answer: D