Pass4Test는 여러분이  Motorola Solutions Certification MSC-235시험 패스와 추후사업에 모두 도움이 되겠습니다.Pass4Test제품을 선택함으로 여러분은 시간과 돈을 절약하는 일석이조의 득을 얻을수 있습니다.Motorola Solutions Certification MSC-235인증시험패스는 아주 어렵습니다. 자기에 맞는 현명한 학습자료 선택은 성공의 지름길을 내딛는 첫발입니다. 퍼펙트한 자료만이  Motorola Solutions Certification MSC-235시험에서 성공할수 있습니다. Pass4Test시험문제와 답이야 말로 퍼펙트한 자료이죠. Pass4Test  Motorola Solutions Certification MSC-235인증시험자료는 100% 패스보장을 드립니다

NO.1 You are designing a 3 site Connect Plus system with 12 repeaters per site, no site controller
redundancy, and 3 control channel-capable repeaters at each site. The average number of
subscribers active at a site may approach 300 at any given time of the day. If this customer
experiences a site controller failure, what symptoms and subscriber behavior would you expect
immediately after the failure occurs?
A. All calls in progress at the site will drop. Subscribers will automatically fall back to digital
conventional, allowing users to utilize any of the site’s repeaters.
B. All calls in progress at the site will drop. All subscribers will attempt to roam to one of the other
sites.
C. Calls in progress will remain until one of the other control-channel capable repeaters assumes
the site controller’s role and then they will drop and register on the new controller.
D. Calls in progress will stay up until they complete normally. Subscribers on the control channel
will attempt to roam to one of the other sites.
Answer: B

NO.2 If there is a failure or reboot of a site controller, which of the following must you consider
regarding
Over The Air (OTA) file transfers (select TWO)?
A. Any transfers in progress at the time of the failure may have to be repeated.
B. The controller will have to be re-entitled for OTA operation after it is back online.
C. If the site controller recovers on a different Control Channel, transfers may have to be
reconfigured.
D. Any pending transfers on that controller will be lost and must be re-queued.
Answer: A,D

NO.3 A Request for Proposal (RFP) for a single-site, operations-critical customer requires you to
respond to the following requirement: “...if the RF site equipment includes network switches,
describe the system behavior in the event of a site LAN switch failure.” Which of the following is
the BEST response to this requirement?
A. Redundant site networking equipment may be specified and configured so as to negate the
impact of a single site LAN switch failure. If redundant networking equipment is not installed,the
failure of a site LAN will not affect calls in-progress, but will make it impossible for subscribers to
register at the site.
B. If the single site LAN switch fails, the site master repeater will begin broadcasting failsoft
messages. All subscribers will revert to failsoft operation. The users may select any site repeater
on which to communicate conventionally.
C. Redundant site networking equipment may be specified and configured so as to negate the
impact of a single site LAN switch failure. If redundant networking equipment is not installed, the
failure of a site LAN switch will cause all calls to drop and the subscribers will attempt to roam to
an operational site.
D. In the case of a single-site system, Connect Plus does not utilize site LAN switches.
Answer: C

NO.4 Your customer operates a 4-site Connect Plus network. Two sites are adjacent to each other,
with
overlapping coverage. The other two sites respectively service two manufacturing plants that are
approximately 900 kilometers (559 miles) apart. There are approximately 30 talkgroups in the
network and 300 subscribers. When creating the Option Board codeplug for this customer’s
portable radios, which of the following is the best strategy to ensure smooth, logical operation?
A. Create a separate zone for each of the 4 sites to contain all the necessary contact and RSSI
settings.
B. Create a single Connect Plus zone that will address all of their necessary RSSI settings and
contact lists.
C. Create 2 Connect Plus zones to contain the different contacts and RSSI settings necessary
with this type of topology.
D. Create 3 separate Connect Plus zones to contain the different contacts and RSSI settings
necessary with this type of topology.
Answer: D

NO.5 Your customer is a rail operator whose system covers approximately 125 kilometers (77 miles)
of
track. Trains travel rapidly, and the operator is using a location tracking application to update their
displayed location as frequently as possible. Location updates are critical, even if this means
putting voice calls into the busy queue. What can you do to ensure this behavior?
A. Make sure that RSSI settings are set to -ll3dBm or less for “RSSI Preferred” in the mobiles in
the trains. This will allow the proper sensitivity to make frequent location updates possible. Give
individual SU records a lower priority than any talkgroup priority.
B. Enhanced GPS must be enabled in the Repeaters and Subscribers. Give individual SU records
a higher priority than any talkgroup priority.
C. Call Sessions Configuration in the Network Manager should be set to 29 for the “Number of
Outbound Data Sessions Allowed” field and somewhat less for the Number of Voice/Inbound Data
sessions field. Give individual SU records a higher priority than any talkgroup priority.
D. Location updates should be optimized by enabling Advanced GPS with GPS Data Revert
channels.
Answer: C

NO.6 You are using the Network Manager to connect to a multisite system. Where can you view the
current state of connections to other sites in this multisite system?
A. Event Log Viewer
B. RealTime Display
C. Site Status Window
D. MultiSite Configuration Window
Answer: C