Pass4Test 에서 제공해드리는 Cisco 400-101 (CCIE Routing and Switching Written Exam v5.0)덤프는 아주 우수한 IT인증덤프자료 사이트입니다. IT업계엘리트한 강사들이 퍼펙트한  Cisco 400-101 (CCIE Routing and Switching Written Exam v5.0)덤프문제집을 제작하여 디테일한 시험문제와 답으로 여러분이 아주 간단히  Cisco 400-101 (CCIE Routing and Switching Written Exam v5.0)시험을 패스할 수 있도록 최선을 다하고 있습니다.

NO.1 By default, how does a GET VPN group member router handle traffic when it is unable to
register to a key server?
A. All traffic is queued until registration is successful or the queue is full.
B. All traffic is forwarded through the router unencrypted.
C. All traffic is forwarded through the router encrypted.
D. All traffic through the router is dropped.
Answer: B

NO.2 Refer to the exhibit.
Which two statements about the device that generated the output are true? (Choose two.)
A. The SPT-bit is set.
B. The sparse-mode flag is set.
C. The RP-bit is set.
D. The source-specific host report was received.
Answer: A,D

NO.3 When EIGRP is used as the IPv4 PE-CE protocol, which two requirements must be configured
before the BGP IPv4 address family can be configured? (Choose two.)
A. the route distinguisher
B. the virtual routing and forwarding instance
C. the loopback interface
D. the router ID
Answer: A,B

NO.4 Refer to the exhibit.
When the link between RtrB and RtrC goes down, multicast receivers stop receiving traffic from the
source for multicast group 229.1.1.1.Which solution will resolve this?
A. adding a static mroute on RtrB and RtrF
B. adding a static unicast route on RtrB and RtrF
C. creating a GRE tunnel between RtrB and RtrD
D. enabling PIM sparse mode on both ends of the link between RtrB and RtrF
Answer: D

NO.5 In a nonbackbone OSPF area, all traffic that is destined to the Internet is routed by using a
default route that is originated by the ABR. Which change in the configuration of the OSPF area type
causes traffic from that area that is destined to the Internet to be dropped?
A. The OSPF area changes from NSSA to totally stubby area.
B. The OSPF area changes from NSSA to regular area.
C. The OSPF area changes from stub area to totally stubby area.
D. The OSPF area changes from stub area to NSSA.
Answer: D

NO.6 Refer to the exhibit.
Which additional configuration is necessary for R1 and R2 to become OSPF neighbors?
A. R1 ! router ospf 1 no passive-interface Fastethernet0/0 !
B. R2 ! router ospf 10 no network 10.1.1.6 0.0.0.0 area 0 network 10.1.1.6 0.0.0.0 area 1 !
C. R1 ! interface FastEthernet0/0 ip ospf mtu-ignore ! R2 ! interface FastEthernet0/1 ip ospf mtu-
ignore !
D. R1 ! no router ospf 1 router ospf 10 network 10.1.1.5 0.0.0.0 area 0
Answer: A

NO.7 Which mechanism can be used on Layer 2 switches so that only multicast packets with
downstream receivers are sent on the multicast router-connected ports?
A. IGMP snooping
B. Router Guard
C. PIM snooping
D. multicast filtering
Answer: C

NO.8 Refer to the exhibit.
Which configuration is missing that would enable SSH access on a router that is running Cisco IOS XE
Software?
A. int Gig0/0/0 management-interface
B. class-map ssh-class match access-group protect-ssh policy-map control-plane-in class ssh-class
police 80000 conform transmit exceed drop control-plane service-policy input control-plane-in
C. control-plane host management-interface GigabitEthernet0/0/0 allow ssh
D. interface Gig0/0/0 ip access-group protect-ssh in
Answer: C