Pass4Test는 고객님의 IT자격증취득의 작은 소원을 이루어지게 도워드리는 IT인증시험덤프를 제공해드리는 전문적인 사이트입니다. Pass4Test 표 Microsoft 70-642시험덤프가 있으면 인증시험걱정을 버리셔도 됩니다. Pass4Test 표 Microsoft 70-642덤프는 시험출제 예상문제를 정리해둔 실제시험문제에 가장 가까운 Microsoft 70-642시험준비공부자료로서 공을 들이지않고도 시험패스가 가능합니다.
NO.1 Your network contains a server named Server1 that runs Windows Server 2008 R2. Server1 is
configured as a DNS server.
You need to ensure that Server1 only resolves queries issued from client computers in the same subnet
as Server1. The solution must ensure that Server1 can resolve Internet host names.
What should you do on Server1?
A. Configure Windows Firewall.
B. Create a conditional forwarder.
C. Modify the routing table.
D. Create a trust anchor.
Answer: A
NO.2 You have a Windows Server 2008 R2 computer that has an IP address of 172.16.45.9/21. The server
is configured to use IPv6 addressing.
You need to test IPv6 communication to a server that has an IP address of 172.16.40.18/21.
What should you do from a command prompt?
A. Type ping 172.16.45.9:::::.
B. Type ping ::9.45.16.172.
C. Type ping followed by the Link-local address of the server.
D. Type ping followed by the Site-local address of the server.
Answer: C
NO.3 Your company has an IPv4 Ethernet network.
A router named R1 connects your segment to the Internet. A router named R2 joins your subnet with a
segment named Private1. The Private1 segment has a network address of 10.128.4.0/26. Your computer
named WKS1 requires access to servers on the Private1 network. The WKS1 computer configuration is
as shown in the following table.
WKS1 is unable to connect to the Private1 network by using the current configuration. You need to add a
persistent route for the Private1 network to the routing table on WKS1.
Which command should you run on WKS1?
A. Route add -p 10.128.4.0/22 10.128.4.1
B. Route add -p 10.128.4.0/26 10.128.64.10
C. Route add -p 10.128.4.0 mask 255.255.255.192 10.128.64.1
D. Route add -p 10.128.64.10 mask 255.255.255.192 10.128.4.0
Answer: B
NO.4 Your network uses IPv4.
You install a server that runs Windows Server 2008 R2 at a branch office. The server is configured with
two network interfaces.
You need to configure routing on the server at the branch office. Which two actions should you perform?
(Each correct answer presents part of the solution. Choose two.)
A. Install the Routing and Remote Access Services role service.
B. Run the netsh ras ip set access ALL command.
C. Run the netsh interface ipv4 enable command.
D. Enable the IPv4 Router Routing and Remote Access option.
Answer: A, D
NO.5 Your network contains 100 servers that run Windows Server 2008 R2. A server named Server1 is
deployed on the network. Server1 will be used to collect events from the Security event logs of the other
servers on the network.
You need to define the Custom Event Delivery Optimization settings on Server1.
Which tool should you use?
A. Event Viewer
B. Task Scheduler
C. Wecutil
D. Wevtutil
Answer: C
NO.6 Your company is designing its public network. The network will use an IPv4 range of 131.107.40.0/22.
The network must be configured as shown in the following exhibit.
You need to configure subnets for each segment.
Which network addresses should you assign?
A. Segment A: 131.107.40.0/23
Segment B: 131.107.42.0/24
Segment C: 131.107.43.0/25
Segment D: 131.107.43.128/27
B. Segment A: 131.107.40.0/25
Segment B: 131.107.40.128/26
Segment C: 131.107.43.192/27
Segment D: 131.107.43.224/30
C. Segment A: 131.107.40.0/23
Segment B: 131.107.41.0/24
Segment C: 131.107.41.128/25
Segment D: 131.107.43.0/27
D. Segment A: 131.107.40.128/23
Segment B: 131.107.43.0/24
Segment C: 131.107.44.0/25
Segment D: 131.107.44.128/27
Answer: A
NO.7 You need to capture the HTTP traffic to and from a server every day between 09:00 and 10:00.
What should you do?
A. Create a scheduled task that runs the Netsh tool.
B. Create a scheduled task that runs the Nmcap tool.
C. From Network Monitor, configure the General options.
D. From Network Monitor, configure the Capture options.
Answer: B
NO.8 Your network contains a server that runs Windows Server 2008 R2. You plan to create a custom script.
You need to ensure that each time the script runs, an entry is added to the Application event log.
Which tool should you use.?
A. Eventcreate
B. Eventvwr
C. Wecutil
D. Wevtutil
Answer: A